SD940 (IXUS120) porting thread - page 40 - DryOS Development - CHDK Forum
« previous next »
Pages: 1 ... 35 36 37 38 39 [40] 41 42 43 44 45 ... 55   Go Down

SD940 (IXUS120) porting thread

  • 542 Replies
  • 202110 Views
*

Offline reyalp

  • ******
  • 14080
Re: SD940 (IXUS120) porting thread
« Reply #390 on: 03 / April / 2011, 16:51:43 »
Advertisements
Quote from: philmoz on 03 / April / 2011, 15:57:32
Quote from: eincognito on 03 / April / 2011, 10:35:04
The "enable symbols" option still doesn't remain selected after you restart the camera. But CDHK starts very quickly!

Did you use 'Reset Files' under the 'Visual Settings' menu?
If so this sets the symbol font file to no file selected so the symbols are disabled each time you restart.
Go into visual settings and reselect the icon_10.rbf symbol file then re-enable the symbols under the OSD settings.

Phil.
Strangely, I wasn't able to reproduce this on d10. Tested
- reset files
- leave alt menu
- reboot camera, symbols are off
- enable symbols, symbols appear
Logged
Don't forget what the H stands for.
*

Offline waterwingz

  • ******
  • 12138
    • Waterwingz
Re: SD940 (IXUS120) porting thread
« Reply #391 on: 04 / April / 2011, 00:32:38 »
Update Note :  stub_entry_2.S for firmware version 1.02C updated to match routines used by f/w 1.03B and 1.03C ports.   Available in autobuild as of changeset 1127.
Logged
Ported :   A1200    SD940   G10    Powershot N    G16
*

Offline eincognito

  • *
  • 21
Re: SD940 (IXUS120) porting thread
« Reply #392 on: 04 / April / 2011, 01:31:15 »
Quote from: reyalp on 03 / April / 2011, 16:51:43
Quote from: philmoz on 03 / April / 2011, 15:57:32
Did you use 'Reset Files' under the 'Visual Settings' menu?
If so this sets the symbol font file to no file selected so the symbols are disabled each time you restart.
Go into visual settings and reselect the icon_10.rbf symbol file then re-enable the symbols under the OSD settings.

Phil.
Strangely, I wasn't able to reproduce this on d10. Tested
- reset files
- leave alt menu
- reboot camera, symbols are off
- enable symbols, symbols appear

Curiously strange indeed. Reselecting the icon_10.rbf symbol file fixed the problem. Thanks Phil!
Logged
*

Offline philmoz

  • *****
  • 3450
    • Photos
Re: SD940 (IXUS120) porting thread
« Reply #393 on: 04 / April / 2011, 04:03:57 »
Quote from: reyalp on 03 / April / 2011, 16:51:43
Strangely, I wasn't able to reproduce this on d10. Tested
- reset files
- leave alt menu
- reboot camera, symbols are off
- enable symbols, symbols appear

Try:
- reset files
- leave alt menu
- reboot camera, symbols are off
- enable symbols, symbols appear
- reboot camera again - do you still have symbols?

Phil.

Logged
CHDK ports:
  sx30is (1.00c, 1.00h, 1.00l, 1.00n & 1.00p)
  g12 (1.00c, 1.00e, 1.00f & 1.00g)
  sx130is (1.01d & 1.01f)
  ixus310hs (1.00a & 1.01a)
  sx40hs (1.00d, 1.00g & 1.00i)
  g1x (1.00e, 1.00f & 1.00g)
  g5x (1.00c, 1.01a, 1.01b)
  g7x2 (1.01a, 1.01b, 1.10b)
*

Offline gesualdo

  • *
  • 11
Re: SD940 (IXUS120) porting thread
« Reply #394 on: 04 / April / 2011, 09:37:15 »
hi guys, any new rumors bout a possible chdk for ixus 120 with 1.01A firmware?
tnx for answer and compliments for your good work
Logged
*

Offline eincognito

  • *
  • 21
Re: SD940 (IXUS120) porting thread
« Reply #395 on: 04 / April / 2011, 12:16:46 »
Quote from: waterwingz on 13 / March / 2011, 19:51:09
Quote from: tommasoferrarese on 13 / March / 2011, 19:35:39
i solved it using cardtricks on a pc to ake my 4Gb card bootable.. thanks for the info!!
EDIT:  so are you using a single paritiion now ?  if so - dual partiitions on the SD940 are still a TBD

I can now confirm that dual partitions on 1.03b works using an 8Gb card. Partitioned the card to 2 partitions using SDM. Made the first 2Mb partition bootable and put the bootdisk.bin there. The second <8Gb partition contained the CDHK directory. After powering up, there was a brief hang, perhaps it crashed, but afterwards CDHK booted normally. When pictures are taken, they are stored on the 2nd partition as expected. DNG/RAW saves there too. "Swap partitions" using the camera behaves as expected.

However, pressing the 'play' button to turn on the camera in playback mode makes the canon startup screen to be displayed, then the camera shuts off (automatically as if it crashed). (Pressing the power button initially had this same effect, but I could not reproduce it after a couple of power on/off cycles, and the camera started normally).
EDIT: The behavior is sporadic; sometimes it starts in playback mode fine, other times it just shuts down.
« Last Edit: 04 / April / 2011, 12:19:28 by eincognito »
Logged
*

Offline waterwingz

  • ******
  • 12138
    • Waterwingz
Re: SD940 (IXUS120) porting thread
« Reply #396 on: 04 / April / 2011, 13:18:28 »
Quote from: eincognito on 04 / April / 2011, 12:16:46
However, pressing the 'play' button to turn on the camera in playback mode makes the canon startup screen to be displayed, then the camera shuts off (automatically as if it crashed). (Pressing the power button initially had this same effect, but I could not reproduce it after a couple of power on/off cycles, and the camera started normally).
EDIT: The behavior is sporadic; sometimes it starts in playback mode fine, other times it just shuts down.

Common problem with recent CHDK releases (and maybe old ones ?) - this does not appear to be SD940 specific.

Details here :  http://chdk.setepontos.com/index.php?topic=6179.msg62619#msg62619
Logged
Ported :   A1200    SD940   G10    Powershot N    G16
*

Offline waterwingz

  • ******
  • 12138
    • Waterwingz
Re: SD940 (IXUS120) porting thread
« Reply #397 on: 04 / April / 2011, 18:41:54 »
Quote from: gesualdo on 04 / April / 2011, 09:37:15
hi guys, any new rumors bout a possible chdk for ixus 120 with 1.01A firmware?

Anyone interested in CHDK for firmware 1.01A should send me a personal message with their real email address.  If I can get a couple of people with that firmware interested and I have contact information for them,  I will consider doing the port.  Its too much work doing the port without some more permanent way to contact those interested.
 

Logged
Ported :   A1200    SD940   G10    Powershot N    G16
*

Offline eincognito

  • *
  • 21
Re: SD940 (IXUS120) porting thread
« Reply #398 on: 05 / April / 2011, 00:45:00 »
How would you edit the user menu? The User Manual says to press the "+/- button or the equivalent button on the camera" when User Menu is set to edit. The half-shoot button doesn't do it either.
« Last Edit: 05 / April / 2011, 01:00:48 by eincognito »
Logged
*

Offline mgg

  • *
  • 16
Re: SD940 (IXUS120) porting thread
« Reply #399 on: 05 / April / 2011, 21:35:55 »
Hi, have a 103c and have downloaded and installed the ixus120_sd940-103c-0.9.9-1118_BETA code successfully.  I tried to install the basic program I currently run on an SD400's - and it fails early.  
If I get_prop 0,x which is camera mode - it always reads 0 no matter where the switches are set.  I switched to x=get_mode - and I always get 1 no matter how the switches are set.

as in:

:TT
x=get_mode
print " camera mode is ",x
if x=1 then goto "DM"
print " Camera MODE error",x
sleep 250
goto "TT"
:DM
set_prop 6 0
set_prop 8 1
set_prop 9 0
print " eval mode",0

I shows x is one, appears to jump to :DM, then crashes somewhere before the print.

My question is - should code like this run in this beta or do I have some problem specific to my setup?

tnx
mgg
« Last Edit: 05 / April / 2011, 21:38:27 by mgg »
Logged
Pages: 1 ... 35 36 37 38 39 [40] 41 42 43 44 45 ... 55   Go Up
« previous next »
 

Related Topics