Having trouble getting the version out of SD980 - page 3 - General Discussion and Assistance - CHDK Forum supplierdeeply
« previous next »
Pages: 1 2 [3] 4   Go Down

Having trouble getting the version out of SD980

  • 33 Replies
  • 19336 Views
*

Offline RaduP

  • *****
  • 926
Re: Having trouble getting the version out of SD980
« Reply #20 on: 12 / September / 2009, 17:56:00 »
Advertisements
Got it, 31e5 :)

USB\Vid_04a9&Pid_31e5&Rev_0002
USB\Vid_04a9&Pid_31e5
Logged
*

Offline reyalp

  • ******
  • 14080
Re: Having trouble getting the version out of SD980
« Reply #21 on: 12 / September / 2009, 19:34:59 »
Quote from: fe50 on 12 / September / 2009, 16:16:41
Quote from: RaduP on 12 / September / 2009, 15:36:58
And how do you get the platform number then?
Connect the camera to a Linux system, look to the number with lsusb, its part #2 of the USB device ID
(e.g. 04a9:318d for the SX10)
Are you sure that what is shown here is the same as the pid ? When I recently checked in the a2000 port it what was listed as the USB id was different than the pid. But that could have been human error somewhere.
Logged
Don't forget what the H stands for.
*

Offline fe50

  • ******
  • 3147
  • IXUS50 & 860, SX10 Star WARs-Star RAWs
    • fe50
Re: Having trouble getting the version out of SD980
« Reply #22 on: 12 / September / 2009, 19:51:07 »
Quote from: reyalp on 12 / September / 2009, 19:34:59
Are you sure that what is shown here is the same as the pid ? When I recently checked in the a2000 port it what was listed as the USB id was different than the pid. But that could have been human error somewhere.
It's the P-ID on all my cams, the SD400, SD870 and the SX10; 31e5 for the SD980 sounds also plausible...would be nice if others would have a look & report...

*Edit:
See also http://www.linux-usb.org/usb.ids and http://www.vpcblog.net/article.asp?id=480 ...
« Last Edit: 12 / September / 2009, 20:10:39 by fe50 »
Logged
*

Offline RaduP

  • *****
  • 926
Re: Having trouble getting the version out of SD980
« Reply #23 on: 12 / September / 2009, 22:08:38 »
Great, it worked and booted (although no LED blinking, so I need to find the LED addresses).
So the version is correct. Thanks fe50 for your help.
Logged
*

Offline reyalp

  • ******
  • 14080
Re: Having trouble getting the version out of SD980
« Reply #24 on: 12 / September / 2009, 22:18:21 »
Quote from: fe50 on 12 / September / 2009, 19:51:07
It's the P-ID on all my cams, the SD400, SD870 and the SX10; 31e5 for the SD980 sounds also plausible...would be nice if others would have a look & report...
Yeah looks like it is correct for my a540.
Logged
Don't forget what the H stands for.
*

Offline fe50

  • ******
  • 3147
  • IXUS50 & 860, SX10 Star WARs-Star RAWs
    • fe50
Re: Having trouble getting the version out of SD980
« Reply #25 on: 13 / September / 2009, 05:17:15 »
To be a bit more precise on this, P-ID vs. USB device ID:

The USB device ID normally contain the camera's P-ID,
but the reported number may vary dependend on the camera's connection mode.

It looks like the P-ID is reported in the USB device ID always when the camera is
connected in PTP mode; on some older Powershots with mass storage
support or with other additional USB protocols the USB ID number may be different
when the camera is connected in one of this modes.
« Last Edit: 13 / September / 2009, 05:28:30 by fe50 »
Logged
*

Offline mindbomb

  • *
  • 1
Re: Having trouble getting the version out of SD980
« Reply #26 on: 16 / September / 2009, 12:59:14 »
I've got a new SD980 yesterday.
I used CHDK on my old A610, which made it awesome.

Any way I can help with advancing a port to the SD980?
Logged
*

Offline RaduP

  • *****
  • 926
Re: Having trouble getting the version out of SD980
« Reply #27 on: 16 / September / 2009, 17:26:01 »
Quote from: mindbomb on 16 / September / 2009, 12:59:14
I've got a new SD980 yesterday.
I used CHDK on my old A610, which made it awesome.

Any way I can help with advancing a port to the SD980?

It depends. Do you have any hardware or software skills?
Logged
*

Offline RaduP

  • *****
  • 926
Re: Having trouble getting the version out of SD980
« Reply #28 on: 16 / September / 2009, 22:39:17 »
Firmware dump started :)
Logged
*

Offline trogdor

  • *
  • 3
Re: Having trouble getting the version out of SD980
« Reply #29 on: 23 / December / 2009, 16:40:38 »
Has anyone figured out how to get the firmware version of the SD980 yet? I'm trying to get CHDK working and I have not been able to get the "firmware update..." menu option to display. When I try to make a bootable SD card the camera does not turn on at all, so I figured that my firmware version might be off, but I can't find it. Help would be much appreciated.
Thanks.
Logged
Pages: 1 2 [3] 4   Go Up
« previous next »
 

Related Topics