SX500 IS Porting thread - DryOS Development - CHDK Forum  
« previous next »
Pages: [1] 2 3 4 5 6   Go Down

SX500 IS Porting thread

  • 53 Replies
  • 19167 Views
*

Offline nafraf

  • *****
  • 1308
SX500 IS Porting thread
« on: 25 / June / 2013, 23:04:26 »
Advertisements
I started a blind port for SX500 100c.  SX500IS firmware is similar to SX160IS, I'm using code_gen.

If someone can test, and give feedback, send me a private message, I'll send you the link to the binary file.
Logged
*

Offline topsun

  • *
  • 2
Re: SX500 IS Porting thread
« Reply #1 on: 27 / June / 2013, 18:59:03 »
Sorry I took so long. I now have this thread on notify. Acid says my Canon Powershot SX 500 is firmware 100c.

 I flash phones all the time, but never a camera. I might have a bit of a learning curve.
Logged
*

Offline oluccas

  • *
  • 2
Re: SX500 IS Porting thread
« Reply #2 on: 29 / June / 2013, 17:10:21 »
That's so great! I've sent you a PM already!
Logged
*

Offline nafraf

  • *****
  • 1308
Re: SX500 IS Porting thread
« Reply #3 on: 29 / June / 2013, 18:11:04 »
Quote from: oluccas on 29 / June / 2013, 17:10:21
That's so great! I've sent you a PM already!
I sent you the link.  topsun reported that CHDK boots and test scripts are running without problems. More tests are needed (RAW capture, photo overrides, etc).
Logged
*

Offline moholt

  • *
  • 1
Re: SX500 IS Porting thread
« Reply #4 on: 03 / July / 2013, 08:10:45 »
Is there any way I could test this as well? I've been desperate to find anything that gives this kind of functionality to this camera.
Logged
*

Offline Luneth Moriticus

  • *
  • 3
Re: SX500 IS Porting thread
« Reply #5 on: 03 / July / 2013, 11:15:05 »
I'd be willing to test this. Been looking around for someone to port it. PM me. THx

Over and out,

                   --Luneth
Logged
*

Offline drixkarasu

  • *
  • 1
Re: SX500 IS Porting thread
« Reply #6 on: 04 / July / 2013, 14:56:51 »
I would love to test it and provide some feedback, I've been waiting for this for a while.

Best regards.
Logged
*

Offline nafraf

  • *****
  • 1308
Re: SX500 IS Porting thread
« Reply #7 on: 04 / July / 2013, 15:52:27 »
@drixkarasu, Lunheth Moriticus and moholt,

I sent the link to you.  It's only for 100c firmware, check your firmware version using ACID
To load it, it is necessary to use bootable sd card method.

If you have a different version firmware, a new port will be necessary.

Please test and report.  Thanks
Logged
*

Offline Luneth Moriticus

  • *
  • 3
Re: SX500 IS Porting thread
« Reply #8 on: 04 / July / 2013, 16:57:06 »
I have a canon powershot sx500 is and I extracted the zip into a formated 4gig fat32 sd. i locked the card and then booted up my camera and all I see is card locked. I'm not sure what I did wrong. a little help here?

thanks
       
           -Luneth
Logged
*

Offline waterwingz

  • ******
  • 12088
    • Waterwingz
Re: SX500 IS Porting thread
« Reply #9 on: 04 / July / 2013, 17:05:11 »
Quote from: Luneth Moriticus on 04 / July / 2013, 16:57:06
I have a canon powershot sx500 is and I extracted the zip into a formated 4gig fat32 sd. i locked the card and then booted up my camera and all I see is card locked. I'm not sure what I did wrong. a little help here?
What you did wrong it not RTFM.   You probably want to start here :

http://chdk.wikia.com/wiki/Prepare_your_SD_card
Logged
Ported :   A1200    SD940   G10    Powershot N    G16
Pages: [1] 2 3 4 5 6   Go Up
« previous next »
 

Related Topics