Firmware dumper CHDK module - page 2 - Firmware Dumping - CHDK Forum
« previous next »
Pages: 1 [2] 3 4 5 6 7   Go Down

Firmware dumper CHDK module

  • 60 Replies
  • 23926 Views
*

Offline ahull

  • *****
  • 634
Re: Firmware dumper CHDK module
« Reply #10 on: 09 / November / 2013, 16:31:04 »
Advertisements
Posted ( http://ubuntuone.com/1SZgHMG4XBmrWjfpQ7yT5s )... see edit to previous message.
Logged
*

Offline ahull

  • *****
  • 634
Re: Firmware dumper CHDK module
« Reply #11 on: 10 / November / 2013, 14:17:52 »
One more ancient camera ROM for the archive. Ixus 70 - 1.01b - PRIMARY.BIN_Ixus70_SD1000.101b

http://ubuntuone.com/2fnNBGfU2VuNo7oOtwnKIQ
« Last Edit: 10 / November / 2013, 14:28:37 by ahull »
Logged
*

Offline srsa_4c

  • ******
  • 4451
Re: Firmware dumper CHDK module
« Reply #12 on: 10 / November / 2013, 15:34:33 »
Quote from: ahull on 10 / November / 2013, 14:17:52
One more ancient camera ROM for the archive. Ixus 70 - 1.01b - PRIMARY.BIN_Ixus70_SD1000.101b

http://ubuntuone.com/2fnNBGfU2VuNo7oOtwnKIQ
Thx.
About the Ixus I zoom: I was wrong. That dump is already in the collection (and I think the "old" dump is from you). Since my quick list is from grepping the CHDK source, it doesn't contain hints about dumps that are from "other" camera versions (supported or unsupported).

I'm collecting the missing ones because there is data in the unknown part of ROM that can be important.

I secretly hope that an S2IS owner will read this thread some day...
Logged
*

Offline Mad Dog

  • *
  • 11
Re: Firmware dumper CHDK module
« Reply #13 on: 17 / November / 2013, 14:58:56 »
Hi there,
I have a Canon S2 IS and I would be happy to help out.
You are going to have to walk me through it as I'm not all that computer savvy.
I tried to load CHDK using STICK but got a message saying "No official build is available for this camera".

Here's some info I got on the camera using the Set/Disp hold down trick:

P-ID 30F0 NT
Firmware Ver GM1.00G
E18
Dec 19 2005

Cheers
Logged
*

Offline srsa_4c

  • ******
  • 4451
Re: Firmware dumper CHDK module
« Reply #14 on: 17 / November / 2013, 15:48:18 »
Quote from: Mad Dog on 17 / November / 2013, 14:58:56
Hi there,
I have a Canon S2 IS and I would be happy to help out.
You are going to have to walk me through it as I'm not all that computer savvy.
Once you have CHDK up and running, try following the instructions at the start of this post. You'll need the module that is linked to the bottom of the same post (memdmper.flt). Ask, if you have any questions.
Logged
*

Offline reyalp

  • ******
  • 14128
Re: Firmware dumper CHDK module
« Reply #15 on: 17 / November / 2013, 16:20:28 »
Quote from: Mad Dog on 17 / November / 2013, 14:58:56
I tried to load CHDK using STICK but got a message saying "No official build is available for this camera".
This must be a problem with stick, there is a 100G version in the autobuild on http://mighty-hoernsche.de/

You should be able to follow the manual instruction on http://chdk.wikia.com/wiki/Prepare_your_SD_card
Logged
Don't forget what the H stands for.
*

Offline Mad Dog

  • *
  • 11
Re: Firmware dumper CHDK module
« Reply #16 on: 18 / November / 2013, 06:32:52 »
Thanks for the replies.

OK, I've got CHDK installed!  (This time without using STICK).

Thanks for your help.
Logged
*

Offline koshy

  • *****
  • 1096
Re: Firmware dumper CHDK module
« Reply #17 on: 14 / July / 2014, 17:36:35 »
One more camera ROM for the archive:

A560 1.00A
Logged
Koshy had a little ELPH which wasn't white as snow but everywhere that Koshy went the ELPH was sure to go. (actually an SD, but that detail ruins the rhyme...)
*

Offline koshy

  • *****
  • 1096
Re: Firmware dumper CHDK module
« Reply #18 on: 14 / July / 2014, 18:05:37 »
I also have these:

a450   100d
g7   100i
a570   101a
a630   100c
s2is   100f

I tried the memdmper.flt on all of them but it didn't work out. I did it in play mode. Either the camera shut off, or it said no memory card or the LED lit up and that was the last of it. Strange. A560 worked just fine... Alternatives?
« Last Edit: 14 / July / 2014, 18:20:27 by koshy »
Logged
Koshy had a little ELPH which wasn't white as snow but everywhere that Koshy went the ELPH was sure to go. (actually an SD, but that detail ruins the rhyme...)
*

Offline srsa_4c

  • ******
  • 4451
Re: Firmware dumper CHDK module
« Reply #19 on: 14 / July / 2014, 18:48:22 »
Quote from: koshy on 14 / July / 2014, 18:05:37
I tried the memdmper.flt on all of them but it didn't work out. I did it in play mode. Either the camera shut off, or it said no memory card or the LED lit up and that was the last of it.
Try again with CHDK 1.2, changes in 1.3 may cause compatibility issues with older modules.
I just tried the module on an a460 running CHDK 1.2 (newest autobuild release), it worked flawlessly.
I'm especially curious how it can make the cam display "no memory card"...
If you could retrieve a romlog from the camera that crashed, that could give some hints.
Quote
Alternatives?
http://chdk.wikia.com/wiki/Canon_Basic/Scripts/Dumper
Logged
Pages: 1 [2] 3 4 5 6 7   Go Up
« previous next »
 

Related Topics


SimplePortal © 2008-2014, SimplePortal