CHDK for the Canon IXUS 240? - General Discussion and Assistance - CHDK Forum
« previous next »
Pages: [1]   Go Down

CHDK for the Canon IXUS 240?

  • 7 Replies
  • 4466 Views
*

Offline 240iger

  • *
  • 5
CHDK for the Canon IXUS 240?
« on: 24 / January / 2014, 10:02:55 »
Advertisements
I have the Canon IXUS 240 and it has the Firmeware 1.01a.
The CHDK is available for Firmeware 1.02A (http://mighty-hoernsche.de/bins/ixus240_elph320hs-102a-1.2.0-3332-full_ALPHA.zip)

Can anyone help me and tell me where I can download the CHDK for the Firmeware 1.01a or where I can update my Firmeware to the Version 1.02a?

Thank you!

240iger
Logged
*

Offline nafraf

  • *****
  • 1308
Re: CHDK for the Canon IXUS 240?
« Reply #1 on: 24 / January / 2014, 11:16:54 »
1.01a/100d was included to autobuild (trunk r3334).  It should be available soon. It is not fully tested, but testers reported that it boots and scripts work. Ixus240 port was done using code_gen, then I hope that it works similar to 1.02a version.

If you find any bug, please report to ixus240 porting thread

Logged
*

Offline 240iger

  • *
  • 5
Re: CHDK for the Canon IXUS 240?
« Reply #2 on: 24 / January / 2014, 12:15:28 »
Thank you!
Logged
*

Offline 240iger

  • *
  • 5
Re: CHDK for the Canon IXUS 240?
« Reply #3 on: 24 / January / 2014, 14:14:19 »
One further Question the Handbook says that the CHDK starts with <ALT>Modus with the [MENU]- Button. IXUS 240 has a Touch-Screen – how can I start the CHDK?
Logged
*

Offline nafraf

  • *****
  • 1308
Re: CHDK for the Canon IXUS 240?
« Reply #4 on: 24 / January / 2014, 14:46:31 »
Touch screen interface is different to standard CHDK.  To enter CHDK 'Alt' mode touch the 'CHDK' button on the screen.
Did you see CHDK logo during boot up?
Try this to load CHDK: http://chdk.wikia.com/wiki/Prepare_your_SD_card#Bootable_SD_Card_Method


Logged
*

Offline 240iger

  • *
  • 5
Re: CHDK for the Canon IXUS 240?
« Reply #5 on: 25 / January / 2014, 09:37:24 »
Figure 1 shows the screen after the installation - the CHDK is visible. After a few seconds, the monitor will turn off.

After I turn the camera normally on with On / Off Switch there is no longer a CHDK Figure 2?
Logged
*

Offline nafraf

  • *****
  • 1308
Re: CHDK for the Canon IXUS 240?
« Reply #6 on: 25 / January / 2014, 12:56:01 »
Quote from: 240iger on 25 / January / 2014, 09:37:24
Figure 1 shows the screen after the installation - the CHDK is visible. After a few seconds, the monitor will turn off.
Do you mean that camera crash after some seconds?  :blink:

Quote
After I turn the camera normally on with On / Off Switch there is no longer a CHDK Figure 2?
If you are using firmware update method to load CHDK, you have to run those steps each time you turn on your camera.
To load CHDK automatically on power up, you need to use Bootable SD-Card method.

Logged
*

Offline 240iger

  • *
  • 5
Re: CHDK for the Canon IXUS 240?
« Reply #7 on: 25 / January / 2014, 13:55:18 »
Yes it crashed after a view seconds!

Now I understand the function!
Logged
Pages: [1]   Go Up
« previous next »
 

Related Topics
SimplePortal 2.3.6 © 2008-2014, SimplePortal