« previous next »
Pages: [1]   Go Down

Build info and zoom value display in Version 1.2 for Canon A1200

  • 3 Replies
  • 1353 Views
*

Offline ripwink

  • **
  • 55
Build info and zoom value display in Version 1.2 for Canon A1200
« on: 04 / February / 2014, 23:20:42 »
Advertisements
Are these bugs in Version 1.2 for Canon A1200?

1. My camera has firmware 100a. and I have installed the matching CHDK. When I check Build Info, it shows FW Vers: 100b.

2. Miscellaneous values: Zoom Value:  Set to EFL. In the display it shows the EFL between 20mm to 80mm. This should most probably be 28 to 112mm.

3. Does A1200 support Override Subj. Dist? If yes then how to make it work.
Logged
*

Offline waterwingz

  • ******
  • 11529
    • Waterwingz
Re: Build info and zoom value display in Version 1.2 for Canon A1200
« Reply #1 on: 04 / February / 2014, 23:39:02 »
Quote from: ripwink on 04 / February / 2014, 23:20:42
Are these bugs in Version 1.2 for Canon A1200?
No.

Quote
1. My camera has firmware 100a. and I have installed the matching CHDK. When I check Build Info, it shows FW Vers: 100b.
That's because some versions of CHDK work for more than one firmware version. Rather than compile seperate versions for both cameras each night,  one version is made and copied under a different name.  If it boots at all, its good.

Quote
2. Miscellaneous values: Zoom Value:  Set to EFL. In the display it shows the EFL between 20mm to 80mm. This should most probably be 28 to 112mm.
If I get a minute I will look at it. But its not exactly a high priority. Sorry.

Quote
3. Does A1200 support Override Subj. Dist? If yes then how to make it work.
http://chdk.wikia.com/wiki/A1200#Notes_on_SD_Override_for_the_A1200
Logged
Ported :   A1200    SD940   G10    Powershot N    G16
*

Offline philmoz

  • *****
  • 3070
    • Photos
Re: Build info and zoom value display in Version 1.2 for Canon A1200
« Reply #2 on: 05 / February / 2014, 00:12:25 »
Quote from: waterwingz on 04 / February / 2014, 23:39:02
Quote
2. Miscellaneous values: Zoom Value:  Set to EFL. In the display it shows the EFL between 20mm to 80mm. This should most probably be 28 to 112mm.
If I get a minute I will look at it. But its not exactly a high priority. Sorry.

Should be fixed in revision 3350 (1.2) and 3349 (1.3).

Phil.
Logged
CHDK ports:
  sx30is (1.00c, 1.00h, 1.00l, 1.00n & 1.00p)
  g12 (1.00c, 1.00e, 1.00f & 1.00g)
  sx130is (1.01d & 1.01f)
  ixus310hs (1.00a & 1.01a)
  sx40hs (1.00d, 1.00g & 1.00i)
  g1x (1.00e, 1.00f & 1.00g)
*

Offline ripwink

  • **
  • 55
Re: Build info and zoom value display in Version 1.2 for Canon A1200
« Reply #3 on: 05 / February / 2014, 01:08:47 »
Thanks for the clarifications on build info display and SD override.
Regards
Logged
Pages: [1]   Go Up
« previous next »
 

Related Topics