Canon A2500 - CHDK Releases - CHDK Forum supplierdeeply
« previous next »
Pages: [1]   Go Down

Canon A2500

  • 7 Replies
  • 5411 Views
*

Offline novsela

  • ***
  • 113
Canon A2500
« on: 18 / June / 2014, 16:23:13 »
Advertisements
Hi all

I will start that I am newbie with CHDK and with this forum in particular , so please forgive for my mistakes :)

I installed the latest a2500-100a-1.3.0-3467-full_ALPHA.zip firmware and found issue with USB REMOTE


it looks like the camera take 2 pictures  instead of just one

I made the following scenario


Install the latest version of CHDK 1.3.0
In the CHDK Settings -> Remote Parameters menu, set Enable Remote to [ * ], Switch Type to [ OnePush ], Control Mode to [ Normal ], Enable Sync to [ * ],  Sync Delay 0.1ms to [ * ] [ 50000 ]
Exit the CHDK menus and then exit <ALT> mode.
Turn the camera off
Turn the camera back on
Put the camera into shooting mode (lens extended)
Plug your USB cable between your PC and camera.
Unplug your USB cable

Result

Camera take 2 picture (shoot twice), first immediately after  I connected to pc, and 5 sec after i disconnected it

I expected that the camera will take single picture 5 seconds after i disconnected .


I would appreciate your help

 
Logged
*

Offline Microfunguy

  • ****
  • 4037
    • StereoData Maker
Re: Canon A2500
« Reply #1 on: 18 / June / 2014, 17:33:49 »
Is the camera in Canon continuous-shooting mode by any chance ?
Logged
*

Offline novsela

  • ***
  • 113
Re: Canon A2500
« Reply #2 on: 18 / June / 2014, 17:58:22 »
No
Logged
*

Offline novsela

  • ***
  • 113
Re: Canon A2500
« Reply #3 on: 18 / June / 2014, 18:42:15 »
I made reset to default , change the setting as previous & verify not in continuous but still it takes two images
Logged
*

Offline waterwingz

  • ******
  • 12138
    • Waterwingz
Re: Canon A2500
« Reply #4 on: 18 / June / 2014, 18:51:15 »
Quote from: novsela on 18 / June / 2014, 18:42:15
I made reset to default , change the setting as previous & verify not in continuous but still it takes two images
Two additional things to try using the same test as you mentioned above.

  • Set the sync delay to 0 (or disable it). Rerun the test.  Does it still take two images?
  • Disable sync completely.  One or two images when you test again?

I'm trying to puzzle out having the wait_until_remote_button_is_released hook inserted in the wrong place in capt_seq.c could cause two pictures to be taken
Logged
Ported :   A1200    SD940   G10    Powershot N    G16
*

Offline novsela

  • ***
  • 113
Re: Canon A2500
« Reply #5 on: 19 / June / 2014, 00:57:55 »
something strange is happening here


1. Set the sync delay to 0 (or disable it), Result :immediately flash  when connecting the USB cable , immediately shoot when disconnecting

2. Disable sync completely , Result - immediately shoot disconnecting ( AS IT SHOULD)


why enable sync create immediately flash ? I am getting black screen after the first flash till i disconnect the USB cable


It looks like I made mistake previous- the camera doesn't  take 2 pictures , instead it shoot 2 flash (one immediately and one after disconnecting ) and one picture
Logged
*

Offline Microfunguy

  • ****
  • 4037
    • StereoData Maker
Re: Canon A2500
« Reply #6 on: 19 / June / 2014, 05:33:51 »
The camera fires the weaker preflash and pauses the capture sequence until you release the USB switch.
It then fires the main flash.
This is completely normal.
Logged
*

Offline novsela

  • ***
  • 113
Re: Canon A2500
« Reply #7 on: 19 / June / 2014, 06:51:10 »
thanks .. I used A1400 before and it perform differently this why i got some concern

thx again  ;)
Logged
Pages: [1]   Go Up
« previous next »
 

Related Topics