Continuous distance measurement - General Discussion and Assistance - CHDK Forum
« previous next »
Pages: [1]   Go Down

Continuous distance measurement

  • 4 Replies
  • 4236 Views
*

Offline nocaC_230

  • *
  • 27
Continuous distance measurement
« on: 20 / August / 2014, 04:31:29 »
Advertisements
Helo,

is it possible to measure and display the distance to an object continuously.

About help I would be very happy.

Greetings
Logged
*

Offline Microfunguy

  • ****
  • 4037
    • StereoData Maker
Re: Continuous distance measurement
« Reply #1 on: 20 / August / 2014, 05:44:59 »
Quote from: nocaC_230 on 20 / August / 2014, 04:31:29
is it possible to measure and display the distance to an object continuously.

Not with any accuracy, and you have to half-press each time to update the reading.

These small-sensor cameras have very large depth-of-field, especially at the wide-angle setting.
The only thing the Canon firmware knows is aperture (if any),focal length and position of the focus stepping motor.
From that it infers focused distance.
A single focus step may move focus from two metres to four metres.
There is better accuracy at long focal lengths.


David
Logged
*

Offline waterwingz

  • ******
  • 12140
    • Waterwingz
Re: Continuous distance measurement
« Reply #2 on: 20 / August / 2014, 07:43:31 »
Quote from: nocaC_230 on 20 / August / 2014, 04:31:29
is it possible to measure and display the distance to an object continuously.
The answer to your question is yes.  All you need is a small CHDK script.

However, as microfunguy points out, the accuracy will not be very good.  In addition, for many of the same reasons, the precision will likely be poor.

So the question you need to ask yourself is how much precision & accuracy do you need ?   Also, the camera will tend to focus on whatever objects it can find near the center of the image. Is that acceptable too?

If you still want to try this,  I can post a small script for you.
Logged
Ported :   A1200    SD940   G10    Powershot N    G16
*

Offline waterwingz

  • ******
  • 12140
    • Waterwingz
Re: Continuous distance measurement
« Reply #3 on: 20 / August / 2014, 09:44:54 »
I was curious to see how well this would actually work. The results were better than I expected using my A1200 but still nothing I would consider a precision measurement.

Code: [Select]
--[[
@title Distance Meter
--]]

function update_display(msg)
    draw_string(xpos,ypos,string.sub(msg, (string.len(msg)/2)-6, (string.len(msg)/2)+5), white, blue, text_size)   
end

    transparent = 256
    black = 257
    white = 258
    red = 259
    green = 263
    blue = 266
    yellow = 271
    xpos =  50
    ypos =  50
    text_size = 2
    strmsg = "    start     "
   
    if ( get_mode() == false ) then             -- switch to shooting mode on start up
       sleep(1000)
       set_record(1)
       while ( get_mode() == false) do sleep(100) end
    end
    sleep(500)   
    repeat
        press("shoot_half")
        count = 0
        repeat
            update_display(strmsg)
            sleep(100)
            count = count + 1
            if (count > 40 ) then timeout = true end
        until (get_shooting() == true ) or (timeout == true) 
        release("shoot_half")
        if ( timeout == true ) then
            strmsg = "  timeout  "
        else
            sd = get_focus()
            if ( sd == -1 ) then
                strmsg = "    infinity     "
            else
                strmsg = "     "..get_focus() .." mm     "
            end
        end
        for i=0, 10, 1 do
            update_display(strmsg)
            sleep(100)
        end
    until false   
Logged
Ported :   A1200    SD940   G10    Powershot N    G16
*

Offline nocaC_230

  • *
  • 27
Re: Continuous distance measurement
« Reply #4 on: 20 / August / 2014, 10:33:35 »
Hi,

thanks, that really helped.
The inaccuracy is not a big problem.

Thanks again, now I can go on.


nocaC_230
Logged
Pages: [1]   Go Up
« previous next »
 

Related Topics


SimplePortal © 2008-2014, SimplePortal