eos M10 port - page 13 - DryOS Development - CHDK Forum
« previous next »
Pages: 1 ... 8 9 10 11 12 [13] 14 15 16 17 18 ... 33   Go Down

eos M10 port

  • 327 Replies
  • 266159 Views
*

Offline connorbisby

  • *
  • 8
Re: eos M10 port
« Reply #120 on: 19 / May / 2017, 09:34:04 »
Advertisements
i tried that but the camera just gives me 3 flashes on the green led and does nothing
Logged
*

Offline waterwingz

  • ******
  • 12140
    • Waterwingz
Re: eos M10 port
« Reply #121 on: 19 / May / 2017, 11:09:53 »
What firmware version does your camera have? It sounds like you are not using a CHDK port that matches your camera's firmware exactly.
Logged
Ported :   A1200    SD940   G10    Powershot N    G16
*

Offline connorbisby

  • *
  • 8
Re: eos M10 port
« Reply #122 on: 19 / May / 2017, 11:33:35 »
thank you for the help i have managed to get it up running but i just need to figure out how to get in the menu system. you was correct in saying i had the wrong firmware version i had the 110d instead of 110f. and the sd card did need to be locked
Logged
*

Offline noahthetruest

  • *
  • 2
Re: eos M10 port
« Reply #123 on: 19 / May / 2017, 12:40:36 »
Okay so when I use STICK to analyze the photo is states No official build is available for this camera. I am using the most recent firmware: 110d.

When reading the instructions for using STICK with an unsupported build step 2 states: next you have to download the zipfile containing the build in question - presumably pointed to by a porting thread on the CHDK Forum.

Where exactly is this "porting thread" that contains the zipfile I need? I found a .BIN file in a previous search of this forum but have not been able to open it. Is there an actual zip file that I can download?

Thanks again.
Logged
*

Offline srsa_4c

  • ******
  • 4451
Re: eos M10 port
« Reply #124 on: 19 / May / 2017, 12:49:38 »
Quote from: noahthetruest on 19 / May / 2017, 12:40:36
Where exactly is this "porting thread" that contains the zipfile I need?
This is the porting thread.
Quote
Is there an actual zip file that I can download?
It's attached to this post.

Quote from: connorbisby on 19 / May / 2017, 11:33:35
i just need to figure out how to get in the menu system
As it's written in the linked post, the playback button is the ALT button (short press=ALT, long press=original function).

http://chdk.wikia.com/wiki/M10
Logged
*

Offline waterwingz

  • ******
  • 12140
    • Waterwingz
Re: eos M10 port
« Reply #125 on: 19 / May / 2017, 13:42:35 »
Quote from: noahthetruest on 19 / May / 2017, 12:40:36
I am using the most recent firmware: 110d.
Please note than the CHDK version 1.00d means that it's for Canon firmware version 1.00d.  That number does not indicate a release date or timing of the CHDK code.
Logged
Ported :   A1200    SD940   G10    Powershot N    G16
*

Offline srsa_4c

  • ******
  • 4451
Re: eos M10 port
« Reply #126 on: 20 / May / 2017, 06:55:15 »
Menu jumping/flickering

Symptoms

When browsing the CHDK menu, the menu's current and previous state flickers back and forth constantly. When outside the menu, CHDK on screen elements (such as the battery display) flicker in a similar manner.

Triggered by (any of the following)

- hybrid auto mode
- face tracking auto focus enabled
- animated drawings on the Canon display
- ...

Workaround

- Avoid the above mentioned modes / settings when browsing the menu
- Only browse the menu in playback mode


The technical cause of this flickering is that CHDK only draws on one of the 2 overlay buffers at any time - the flickering modes switch constantly back and forth between the two buffers where one of the buffers has outdated CHDK drawings.
« Last Edit: 07 / July / 2018, 16:33:23 by srsa_4c »
Logged
*

Offline axman

  • ***
  • 145
Re: eos M10 port
« Reply #127 on: 21 / May / 2017, 20:45:21 »
Sorry to be so late to the party.  Just upgraded Canon firmware to 1.1.0 d.  The m10-110d-1.5.0-4806-full build works fine for me; CHDK and ALT menus are crisp and nice looking; I can move the cursor using either rotary dial on back, or jogdial on the top.  Normal testing with scripts is next.  If there's a way to provoke the issue, I'm happy to try.
Logged
*

Offline srsa_4c

  • ******
  • 4451
Re: eos M10 port
« Reply #128 on: 22 / May / 2017, 12:27:11 »
@axman
This post quotes the only report about a possibly misbehaving M10 and has a link to a video made by an EOS M3 user who also seems to be affected by something similar.
I suspect a slight misalignment of the jogdial - which, apparently, does not bother the Canon firmware.
So, I'm afraid there's no way to reproduce the issue unless the camera is an affected one.
Logged
*

Offline axman

  • ***
  • 145
Re: eos M10 port
« Reply #129 on: 22 / May / 2017, 12:40:01 »
@srsa_4c,

Ok, thanks.  I can provide a firmware dump of 1.1.0 d from my recently-upgraded camera, if that's still useful.
Logged
Pages: 1 ... 8 9 10 11 12 [13] 14 15 16 17 18 ... 33   Go Up
« previous next »
 

Related Topics
SimplePortal 2.3.6 © 2008-2014, SimplePortal