Thank you so much (: I’m actually looking for a build that will allow me to override the 30min display shut off. Do you know if anything like that exists?
I’ve already found a workaround to get clean hdmi, just need the display to stay on for a longer period of time.
Quote from: srsa_4c on 03 / June / 2019, 16:48:35Code: [Select]' clean rec mode palette' EOS M100, 100a, 101aDIM palette_buffer_ptr = 0x116f4DIM active_palette_buffer = 0x116ecDIM palette_to_zero = 0public sub check_compat() check_compat = 0 if Peek16(0xe1f20270) <> 0x32d1 then exit sub end if if strcmp("GM1.00A",0xe047b5b1) = 0 then check_compat = 1 exit sub end if if strcmp("GM1.01A",0xe047b5cd) = 0 then check_compat = 1 exit sub end ifend subprivate sub RegisterProcs() System.Create() UI.CreatePublic()end subprivate sub palette_mod() adr = *palette_buffer_ptr adr = adr + (palette_to_zero * 4) if *adr <> 0 then adr = *adr + 4 memset(adr, 0, 256 * 4) end ifend subprivate sub Initialize() RegisterProcs() ret = check_compat() if ret=1 then LockMainPower() palette_mod() end ifend subI have Canon EOS M100 (firmware 101a) and "clean HDMI overlay" and "Display off" is functional ... thanks a lot for script! :-)
Code: [Select]' clean rec mode palette' EOS M100, 100a, 101aDIM palette_buffer_ptr = 0x116f4DIM active_palette_buffer = 0x116ecDIM palette_to_zero = 0public sub check_compat() check_compat = 0 if Peek16(0xe1f20270) <> 0x32d1 then exit sub end if if strcmp("GM1.00A",0xe047b5b1) = 0 then check_compat = 1 exit sub end if if strcmp("GM1.01A",0xe047b5cd) = 0 then check_compat = 1 exit sub end ifend subprivate sub RegisterProcs() System.Create() UI.CreatePublic()end subprivate sub palette_mod() adr = *palette_buffer_ptr adr = adr + (palette_to_zero * 4) if *adr <> 0 then adr = *adr + 4 memset(adr, 0, 256 * 4) end ifend subprivate sub Initialize() RegisterProcs() ret = check_compat() if ret=1 then LockMainPower() palette_mod() end ifend sub
' clean rec mode palette' EOS M100, 100a, 101aDIM palette_buffer_ptr = 0x116f4DIM active_palette_buffer = 0x116ecDIM palette_to_zero = 0public sub check_compat() check_compat = 0 if Peek16(0xe1f20270) <> 0x32d1 then exit sub end if if strcmp("GM1.00A",0xe047b5b1) = 0 then check_compat = 1 exit sub end if if strcmp("GM1.01A",0xe047b5cd) = 0 then check_compat = 1 exit sub end ifend subprivate sub RegisterProcs() System.Create() UI.CreatePublic()end subprivate sub palette_mod() adr = *palette_buffer_ptr adr = adr + (palette_to_zero * 4) if *adr <> 0 then adr = *adr + 4 memset(adr, 0, 256 * 4) end ifend subprivate sub Initialize() RegisterProcs() ret = check_compat() if ret=1 then LockMainPower() palette_mod() end ifend sub
Tried it multiple times and tried everything I've thought of. Could it be that I'm using parallels on my MacBook to do the EOScard prep?
Firmware Revision is 1.01 rev 1.00
Quote from: stealtheye95 on 06 / June / 2020, 04:01:55Tried it multiple times and tried everything I've thought of. Could it be that I'm using parallels on my MacBook to do the EOScard prep?Your problem is the card. Preparing the card seems problematic for some people, for reasons I don't know.Have you tried this app (listed on the linked page): http://www.zenoshrdlu.com/macboot/macboot.html ?If you still can't get the script to run, try low level formatting the card (or even fill it with zeroes before), then use MacBoot on it again. You could also try another card, preferably smaller (SD or SDHC).The script has successfully run if the overlays disappear in shooting mode.QuoteFirmware Revision is 1.01 rev 1.00is version 101a, supported by the script. There is not need to re-install it (updating to the same firmware is not supported anyway).
Started by psxpetey General Discussion and Assistance
Started by pigeonhill General Help and Assistance on using CHDK stable releases
Started by oPryzeLP General Discussion and Assistance
Started by platinummack « 1 2 3 4 » General Help and Assistance on using CHDK stable releases
Started by scinos General Discussion and Assistance