IXUS 285 ( IXUS285 ) - page 3 - DryOS Development - CHDK Forum supplierdeeply
« previous next »
Pages: 1 2 [3] 4 5 6   Go Down

IXUS 285 ( IXUS285 )

  • 50 Replies
  • 13294 Views
*

Offline blackhole

  • *****
  • 926
  • A590IS 101b
    • Planetary astrophotography
Re: IXUS 285 ( IXUS285 )
« Reply #20 on: 19 / April / 2020, 05:16:08 »
Advertisements
We need one of the users to test one change that is necessary for the proper functioning of the CHDK for this camera.
The behavior of the POWER (on / off) and PLAY buttons should be checked.
The power up behavior depends on the button used:
- Playback (PLAY) button pressed, camera should start in playback mode.
- POWER (on / off) button pressed for less than a second, camera should start in playback mode.
- POWER (on / off) button pressed for more than a second, camera should start in record mode, with extended lens.
A test version of CHDK is attached.
Logged
*

Offline bbk

  • *
  • 6
Re: IXUS 285 ( IXUS285 )
« Reply #21 on: 07 / September / 2020, 04:06:22 »
@blackhole ... Thanks for the build.
I have the new(est) ? firmware for Canon IXUS 285 HS -  100c .
Wondering if there is a alpha build for that  - Am willing to do the testing for the same with a camera at my disposal.
Just to check my luck i tried the 100b build - but doesn't work on that.
Is it theoretically possible to backtrack my firmware to 100b ? ( from 100c ? )
Logged
*

Offline blackhole

  • *****
  • 926
  • A590IS 101b
    • Planetary astrophotography
Re: IXUS 285 ( IXUS285 )
« Reply #22 on: 07 / September / 2020, 04:29:06 »
Quote from: bbk on 07 / September / 2020, 04:06:22
... Thanks for the build.
I have the new(est) ? firmware for Canon IXUS 285 HS -  100c .
Wondering if there is a alpha build for that  - Am willing to do the testing for the same with a camera at my disposal.
Just to check my luck i tried the 100b build - but doesn't work on that.
Is it theoretically possible to backtrack my firmware to 100b ? ( from 100c ? )
I don't have access to the 100c firmware so I can't tell you anything about compatibility with version 100b.
It is necessary to make a firmware dump, here is how to do it:
https://chdk.fandom.com/wiki/Canon_Basic/Card_Setup
https://chdk.fandom.com/wiki/Canon_Basic/Scripts/Dumper
Logged
*

Offline bbk

  • *
  • 6
Re: IXUS 285 ( IXUS285 )
« Reply #23 on: 07 / September / 2020, 07:43:20 »
Quote from: blackhole on 07 / September / 2020, 04:29:06
Quote from: bbk on 07 / September / 2020, 04:06:22
... Thanks for the build.
I have the new(est) ? firmware for Canon IXUS 285 HS -  100c .
Wondering if there is a alpha build for that  - Am willing to do the testing for the same with a camera at my disposal.
Just to check my luck i tried the 100b build - but doesn't work on that.
Is it theoretically possible to backtrack my firmware to 100b ? ( from 100c ? )
I don't have access to the 100c firmware so I can't tell you anything about compatibility with version 100b.
It is necessary to make a firmware dump, here is how to do it:
https://chdk.fandom.com/wiki/Canon_Basic/Card_Setup
https://chdk.fandom.com/wiki/Canon_Basic/Scripts/Dumper

Thanks for the response.
I have the dump for IXUS 285 100c here
https://drive.google.com/drive/folders/1rC1dsAloiH5r_s-CdYWwz_DjH9IGajnv?usp=sharing


[ I have also tested both the firmware versions for 100b that you posted on the thread. - but both are not compatible on the one I have that has 100c.  ixus285_elph360hs-100b-1.5.0-5130-full / ixus285_elph360hs-100b-1.5.0-pwr_on_test-full_ALPHA ]
Logged
*

Offline blackhole

  • *****
  • 926
  • A590IS 101b
    • Planetary astrophotography
Re: IXUS 285 ( IXUS285 )
« Reply #24 on: 07 / September / 2020, 07:49:47 »
Quote from: bbk on 07 / September / 2020, 07:43:20



Thanks for the response.
I have the dump for IXUS 285 100c here
https://drive.google.com/drive/folders/1rC1dsAloiH5r_s-CdYWwz_DjH9IGajnv?usp=sharing


[ I have also tested both the firmware versions for 100b that you posted on the thread. - but both are not compatible on the one I have that has 100c.  ixus285_elph360hs-100b-1.5.0-5130-full / ixus285_elph360hs-100b-1.5.0-pwr_on_test-full_ALPHA ]
OK, I'll take a look.
Logged
*

Offline blackhole

  • *****
  • 926
  • A590IS 101b
    • Planetary astrophotography
Re: IXUS 285 ( IXUS285 )
« Reply #25 on: 07 / September / 2020, 09:13:44 »
@bbk
You can try this test build.

The differences are minimal, mostly the addresses of some tables in stubs_entry.S, RAM code and RAM data are copied from different addresses, but there are also two different addresses in boot.c
Firmware_crc is disabled.

The source code for the platform / sub / 100c is attached.

EDIT: source code removed
« Last Edit: 08 / September / 2020, 10:51:52 by blackhole »
Logged
*

Offline bbk

  • *
  • 6
Re: IXUS 285 ( IXUS285 )
« Reply #26 on: 07 / September / 2020, 09:43:37 »
@blackhole
Awesome ! Thank a lot for the quick response.
I did load the new build and it works fine so far !
I will test out all the functionalities and drop a message shortly !
Thanks again !
Logged
*

Offline blackhole

  • *****
  • 926
  • A590IS 101b
    • Planetary astrophotography
Re: IXUS 285 ( IXUS285 )
« Reply #27 on: 07 / September / 2020, 11:02:15 »
Quote from: bbk on 07 / September / 2020, 09:43:37
Awesome ! Thank a lot for the quick response.
I did load the new build and it works fine so far !
I will test out all the functionalities and drop a message shortly !
Thanks again !
OK, enjoy.
Can you please do a test as described here:
https://chdk.setepontos.com/index.php?topic=13604.msg143260#msg143260
It is important to know if it works as described.
Logged
*

Offline bbk

  • *
  • 6
Re: IXUS 285 ( IXUS285 )
« Reply #28 on: 07 / September / 2020, 23:14:52 »
Quote from: blackhole on 07 / September / 2020, 11:02:15
OK, enjoy.
Can you please do a test as described here:
https://chdk.setepontos.com/index.php?topic=13604.msg143260#msg143260
It is important to know if it works as described.
@blackhole
Since it didnt have the ps.fi2 or ps.fir file, couldnt try the firmware update method.
So, loaded with the Bootable SD card method.

Here are the test case results -
- #1 ) Playback (PLAY) button pressed, camera should start in playback mode.
Result : Not working. It goes into the record mode, with the lens extended

#2) POWER (on / off) button pressed for less than a second, camera should start in playback mode.
Result : Not working. It goes as into record mode with lens extended.

#3) POWER (on / off) button pressed for more than a second, camera should start in record mode, with extended lens.
Result : Working . Goes to the record mode with lens extended.

I have been testing the other functionalities as well. Let me know if you need to test anything in specific.
Logged
*

Offline blackhole

  • *****
  • 926
  • A590IS 101b
    • Planetary astrophotography
Re: IXUS 285 ( IXUS285 )
« Reply #29 on: 08 / September / 2020, 04:04:54 »
Quote from: bbk on 07 / September / 2020, 23:14:52

Since it didnt have the ps.fi2 or ps.fir file, couldnt try the firmware update method.
So, loaded with the Bootable SD card method.

Here are the test case results -
- #1 ) Playback (PLAY) button pressed, camera should start in playback mode.
Result : Not working. It goes into the record mode, with the lens extended

#2) POWER (on / off) button pressed for less than a second, camera should start in playback mode.
Result : Not working. It goes as into record mode with lens extended.

#3) POWER (on / off) button pressed for more than a second, camera should start in record mode, with extended lens.
Result : Working . Goes to the record mode with lens extended.

I have been testing the other functionalities as well. Let me know if you need to test anything in specific.
Thanks, the values in the trunk are definitely wrong for this camera.
This test build should fix that.
Now you can also try the fw-update method to load the chdk.
Let me know if you find any other problems.
If all goes well, I will replace the source code in the previous post with the final version.
Logged
Pages: 1 2 [3] 4 5 6   Go Up
« previous next »
 

Related Topics