How to Dump Firmware ? - page 4 - Firmware Dumping - CHDK Forum
« previous next »
Pages: 1 2 3 [4] 5 6 7 8   Go Down

How to Dump Firmware ?

  • 78 Replies
  • 153811 Views
*

Offline jak5280

  • *
  • 13
Re: How to Dump Firmware ?
« Reply #30 on: 09 / November / 2008, 10:10:49 »
Advertisements
I am using the 16MB card that shipped with the camera.  Not sure if I have any others sizes except the 2GBs - I do have several 16MBs, so I'll try a different one.  Could 16MB be too small?
Logged
*

Offline fe50

  • ******
  • 3152
  • IXUS50 & 860, SX10 Star WARs-Star RAWs
    • fe50
Re: How to Dump Firmware ?
« Reply #31 on: 09 / November / 2008, 10:17:10 »
Quote from: jak5280 on 09 / November / 2008, 10:10:49
I am using the 16MB card that shipped with the camera.  Not sure if I have any others sizes except the 2GBs - I do have several 16MBs, so I'll try a different one.  Could 16MB be too small?
No, the 16MB one is perfect...I dumped my SD400 (Ixus 50) successfully with the 16MB card and Cardtricks 1.41 on my first reply to your post...
Logged
*

Offline whim

  • ******
  • 2046
  • A495/590/620/630 ixus70/115/220/230/300/870 S95
Re: How to Dump Firmware ?
« Reply #32 on: 09 / November / 2008, 12:11:01 »
@fe50
@jak5280

Strange... could it be that this cam doesn't work with 0-padded diskboot.bin, or requires a memclr like DryOS ?
anyway, here's some more diskboot.bin's to try out.
i'm attaching what i found in my udumper archives, udumper2.zip contains the vxworks versions that
were included in older (pre-newdryos) versions of CT.
udumper.zip is even older, try the ones in FF810000 directory first (AFAIK all ixus' firmware starts there)

also attached is a pic of what the beginning of a VxWorks dump looks like in BinText

hope that helps,

wim
Logged
*

Offline jak5280

  • *
  • 13
Re: How to Dump Firmware ?
« Reply #33 on: 09 / November / 2008, 12:54:58 »
whim,

Do I simply copy those files onto the formatted disk, or should I substitute the files into the carktricks directory and reformat?
Logged
*

Offline jak5280

  • *
  • 13
Re: How to Dump Firmware ?
« Reply #34 on: 09 / November / 2008, 13:49:07 »
Whim,

I copied each of the diskboot.bin files onto my formatted disk and tried dumping - net result was nothing.  I tried substituting the 8KB empty.DUM and again each diskboot.bin and nothing. Not sure what is next.  :(

I also tried this on a second SD430 camera (ver.req gives same firmware version and NoError.

I appreciate the help, but may be looking for a different camera model.

Logged
*

Offline jak5280

  • *
  • 13
Re: How to Dump Firmware ?
« Reply #35 on: 09 / November / 2008, 16:13:43 »
fe50 or whim,

Just to double check on the procedure:

I place the write protected bootable disk in the camera and press power and wait 1+ minute, then remove the battery and the card.  Is that correct? This is really bugging me.
Logged
*

Offline fe50

  • ******
  • 3152
  • IXUS50 & 860, SX10 Star WARs-Star RAWs
    • fe50
Re: How to Dump Firmware ?
« Reply #36 on: 09 / November / 2008, 16:33:28 »
Quote from: jak5280 on 09 / November / 2008, 16:13:43
Just to double check on the procedure:
I place the write protected bootable disk in the camera and press power and wait 1+ minute, then remove the battery and the card.  Is that correct? This is really bugging me.
Yes, it's correct & the cam must be powered on in playback mode.
Logged
*

Offline jak5280

  • *
  • 13
Re: How to Dump Firmware ?
« Reply #37 on: 09 / November / 2008, 16:39:05 »
Yes, I am powering it on in playback mode.  When I do this there is no response from the camera - but that is what is supposed to happen as well - right?
Logged
*

Offline fe50

  • ******
  • 3152
  • IXUS50 & 860, SX10 Star WARs-Star RAWs
    • fe50
Re: How to Dump Firmware ?
« Reply #38 on: 09 / November / 2008, 16:56:54 »
Quote from: jak5280 on 09 / November / 2008, 16:39:05
Yes, I am powering it on in playback mode.  When I do this there is no response from the camera - but that is what is supposed to happen as well - right?
Yes, you'll get/see absolutely no response. The only sign for a written dump is the content of the empty.dum - file: this file first is completely filled with zeros ( 0 ), the dumper writes the firmware into this file. After that the file has also a lot of leading zeros, but "Show strings" goes over them and shows you some strings from the firmware (see wim's screenshot above).

So it's that simple: no strings means no dump...
Logged
*

Offline ewavr

  • ****
  • 1057
  • A710IS
Re: How to Dump Firmware ?
« Reply #39 on: 09 / November / 2008, 16:59:28 »
Can I ask stupid question: what for to do dump SD430 1.00F if exists official firware update 1.10A?

Official Canon firmware updates - CHDK Wiki
[DOWNLOAD LINKS] Firmware dumps available
Logged
Pages: 1 2 3 [4] 5 6 7 8   Go Up
« previous next »
 

Related Topics


SimplePortal © 2008-2014, SimplePortal