IR Remote using IR Helicopter - General Chat - CHDK Forum supplierdeeply
« previous next »
Pages: [1] 2   Go Down

IR Remote using IR Helicopter

  • 12 Replies
  • 12994 Views
*

Offline RaduP

  • *****
  • 926
IR Remote using IR Helicopter
« on: 17 / July / 2008, 00:48:13 »
Advertisements
Well, today I was reading some other thread here about someone trying to use a doorbell as a RC, then someone else saying they did the same with a RC car, so that inspired me to make this hack.
Basically, I had one of those very small, IR helicopters that got broken (which is something that will happen to them in a short time). I took the logic board out a long time ago, thinking that maybe I will need it for something in the future.

Well, the hack is simple: Removed the motors, connected a mini USB cable (red and black wires) to the main motor output, and voila, now I have a very small IR remote. I tested it indoors, it works from at least 10 meters away, and it will work even if you are in another room (it doesn't always work, I guess it is because my walls are white). I didn't have time to test it outside yet, but it should work well from a close distance.

Here are some photos for your enjoyment (this thing is really smaller that it looks, the connector is a mini USB connector after all).

Logged
*

Offline cybertooth

  • *
  • 5
Re: IR Remote using IR Helicopter
« Reply #1 on: 21 / July / 2008, 01:18:11 »
Great , what is the silver pack below?
Logged
*

Offline vk2him

  • *
  • 22
  • Canon S5IS
Re: IR Remote using IR Helicopter
« Reply #2 on: 21 / July / 2008, 07:14:40 »
Quote from: cybertooth on 21 / July / 2008, 01:18:11
Great , what is the silver pack below?

Battery?  :-X
Logged
*

Offline RaduP

  • *****
  • 926
Re: IR Remote using IR Helicopter
« Reply #3 on: 21 / July / 2008, 12:31:16 »
Yeah, that would be the battery :)
Logged
*

Offline wontolla

  • ****
  • 413
  • S3 & G9 & A720
Re: IR Remote using IR Helicopter
« Reply #4 on: 21 / July / 2008, 18:34:53 »
Hi RaduP!

If I buy one of those helicopters and it "accidentally" gets broken I'll blame you. :)

One question: Does the battery provides 5 volts?
Logged
*

Offline RaduP

  • *****
  • 926
Re: IR Remote using IR Helicopter
« Reply #5 on: 21 / July / 2008, 20:41:38 »
It's a LiPoly battery, it provides 3.7 to 4.2V, so it should work with pretty much all the cameras.
But you might want to buy a cheap radio controlled plane, since they have a longer range than IR.
Logged
*

Offline Emiiiiiil

  • *
  • 36
Re: IR Remote using IR Helicopter
« Reply #6 on: 21 / July / 2008, 21:14:28 »
very clever,i guess the usb setup works with any on/off remote port?
on the doorbell its the bells output,or for any remote controlled vehicle the motor,
now how if i got a remote controlled car,i could use the motor output for the shutter,and the
turning output for turning the camera on a motor mount.or am i being optimistic here,
seems there is basis for some cewl rigs.
btw ir will show,on the picture wont it??unless ur behind the camera!
Logged
*

Offline RaduP

  • *****
  • 926
Re: IR Remote using IR Helicopter
« Reply #7 on: 21 / July / 2008, 23:15:59 »
Yes, you can do use one motor for triggering, the other for moving the camera left/right (or even up and down, if you have a 3 channel controller).
But make sure you check the motor voltage, it should be around 3.5-4V, and should not go higher than 5.5v or so (or you can burn your camera).
The IR doesn't show in an outdoor scene, because there is much more IR from the sun than from the remote. Cameras have IR cutoff filters, so IR RCs are not an issue unless if you point it directly at the lenses.
Of course, you might want to point the IR receptor in the back of the camera, so you have more control of where you point it at.
Logged
*

Offline vine

  • ***
  • 124
  • A560
    • my chdk page
Re: IR Remote using IR Helicopter
« Reply #8 on: 22 / July / 2008, 05:54:26 »
Quote from: RaduP on 21 / July / 2008, 23:15:59
...
But make sure you check the motor voltage, it should be around 3.5-4V, and should not go higher than 5.5v or so (or you can burn your camera).
...

Depending on your camera you can go up to 10V. Check the attached schematic (RN4983 has 10V max in). This was done on purpose because many cheap PC mainboards are known to have unstable USB voltage. So I would assume that similar tolerance was built into every Canon camera, but check your cameras schematics, or read about peoples experiences with higher voltages on this forum before trying anything potentially risky.
« Last Edit: 22 / July / 2008, 11:44:32 by vine »
Logged
my photo map

my chdk page with tutorials, scripts and more

>> finally back from vacation (was a bit longer than intended) <<
*

Offline Emiiiiiil

  • *
  • 36
Re: IR Remote using IR Helicopter
« Reply #9 on: 22 / July / 2008, 10:19:54 »
Thx.no remote controlled toy,is safe from now on.
im going to reak havoc on every gadget i can get my hands on.
Logged
Pages: [1] 2   Go Up
« previous next »
 

Related Topics
SimplePortal 2.3.6 © 2008-2014, SimplePortal