A590IS porting... - page 10 - DryOS Development - CHDK Forum

A590IS porting...

  • 968 Replies
  • 418793 Views
*

Offline fgagnon

  • *
  • 11
  • A540, A590, 40D
Re: A590IS porting...
« Reply #90 on: 22 / October / 2008, 09:59:43 »
Advertisements
Hi all i have a 590 101b and i would like to try chdk but i have no idea where a can find the software can someone send a link or point me in the right direction please
See attachment in Reply #76

*

Offline gho

  • *
  • 37
Re: A590IS porting...
« Reply #91 on: 22 / October / 2008, 10:08:04 »
@fgagnon

1. Power camera on in shooting mode
2. Press the direct print button (the one with the blue light) and notice blue <alt> on display
3. Press the menu button
4. Navigate down to "debug parameters" with the cross
5. Press func set
6. Switch debug data display to none with func set
7. Press menu again
8. Have fun
9. Switch off RAW shooting for now and have even more fun... Edit: (RAW saving works now!)
10. RTFM  ;)

HTH
« Last Edit: 28 / October / 2008, 19:00:11 by gho »

*

Offline fgagnon

  • *
  • 11
  • A540, A590, 40D
Re: A590IS porting...
« Reply #92 on: 22 / October / 2008, 10:19:43 »
@ 2. Press the direct print button (the one with the blue light) and notice blue <alt> on display

Unfortunately, that didn't work.
At least not until I pressed it a couple of times.

When I changed the debug data display to none and went back, the camera bricks with the lens extended.
I'll try reloading CHDK onto the card to reset it and see what happens.
   
 =============

Reloaded CHDK onto the camera card. 
All is well-behaved (except the issue with one-at-a-time RAW shots)
One minor difference is that I deleted the ver.req file (keeping the vers.req file).  I do not know if that was the source of any of my difficulties in accessing the ALT menu, or the bricked bahavior that followed, but: 
Now I am having fun, fun, fun. :)

One (minor) issue is that the [ R G B ] histogram mode displays the third histogram mostly off-screen.
Still cannot decode the RAW files.  I have downloaded and will install the latest UFraw with GIMP to see if that helps.
« Last Edit: 22 / October / 2008, 10:56:37 by fgagnon »

*

Offline gho

  • *
  • 37
Re: A590IS porting...
« Reply #93 on: 22 / October / 2008, 10:24:45 »
@ 2. Press the direct print button (the one with the blue light) and notice blue <alt> on display

When I changed the debug data display to none and went back, the camera bricks with the lens extended.
I'll try reloading CHDK onto the card to reset it and see what happens.   

Yes, and maybe switch off "save RAW" in the RAW parameters submenu for now, as shooting RAW brings the cam in a not very responsive state. Good luck.

*

Offline ma_jk

  • **
  • 60
Re: A590IS porting...
« Reply #94 on: 22 / October / 2008, 10:33:23 »

Before i call this a stable version, id like you to test it.

Changes:
- no more lockups for 1.00E in raw shooting

To Do:
- implement movies control (low priority)
- test again raw file output


*

Offline gho

  • *
  • 37
Re: A590IS porting...
« Reply #95 on: 22 / October / 2008, 10:42:26 »

Before i call this a stable version, id like you to test it.

Changes:
- no more lockups for 1.00E in raw shooting
...

Tested in 101b. No more RAW lockups here too, the image quality is stunning (UFRaw)!
 

Re: A590IS porting...
« Reply #96 on: 22 / October / 2008, 10:50:28 »
Thanks[/quote]
A590IS, Kyocera M410R

Re: A590IS porting...
« Reply #97 on: 22 / October / 2008, 11:32:14 »
Hi I tested it on my cam, 1.01B...
Well I can see the menue and so on  - need to check the manual, what its all about - basicly I tried RAW-Shooting, so I put it on (the little dot inside the field) but it still doesn't seem to work ;) there is some stuff flickering through the left edge (eggtimer, started interrupted or sth ^^) and it doesnt take pics (but it does with RAW switched off)
after some while trying then the display turns black with the lens extended as described before

as gho says it ran with his cam, what did I do wrong? ;)
« Last Edit: 22 / October / 2008, 11:35:30 by zeratul »

*

Offline ma_jk

  • **
  • 60
Re: A590IS porting...
« Reply #98 on: 22 / October / 2008, 11:36:42 »
Hi I tested it on my cam, 1.01B...
Well I can see the menue and so on  - need to check the manual, what its all about - basicly I tried RAW-Shooting, so I put it on (the little dot inside the field) but it still doesn't seem to work ;) there is some stuff flickering through the left edge and it doesnt take pics (but it does with RAW switched off)

as gho says it ran with his cam, what did I do wrong? ;)

Are you sure you took the right bin image for your firmware? version 101b does not stuck on raw.
For the flickering artifacts, move through the menu to enable/disable any appropriate infos you might need.

*

Offline whim

  • ******
  • 2046
  • A495/590/620/630 ixus70/115/220/230/300/870 S95
Re: A590IS porting...
« Reply #99 on: 22 / October / 2008, 11:42:54 »
@zeratul

Quote
...some stuff flickering through the left edge (eggtimer, started interrupted or sth ^^)...

that sounds like your trying to shoot pics while in <Alt> mode (default script will run then)...
remember, you only need to go into <Alt> to set CHDK options, after you did that leave <Alt> and then
take pics.

wim

 

Related Topics


SimplePortal © 2008-2014, SimplePortal