the sx10 porting thread

originalstarlite

1

Re: the sx10 porting thread

« Reply #380 on: 20 / June / 2009, 07:33:21 »

Advertisements

A while back I saw a couple of jpeg's of the battery icon done in 3D. They sure did look great and I have been hoping that someone would add these to the build.

http://chdk.setepontos.com/index.php/topic,3443.0.html

Logged

jlly

1

Re: the sx10 porting thread

« Reply #381 on: 20 / June / 2009, 11:37:46 »

Nimrod, thank you for your efforts. my 101b version need RAW and remote control

although not very technically inclined i am prepared to assist where possible.

Logged

Sunflower

25

Re: the sx10 porting thread

« Reply #382 on: 20 / June / 2009, 17:37:41 »

Quote from: fe50 on 20 / March / 2009, 16:37:57

- power your cam on, half-press the shutter to go to record mode
- press PRINT, then press FUNC/SET
- select "Load script from file", go 2 steps down to the TEST/ folder, press FUNC/SET
- select "BADPIXEL.LUA", press FUNC/SET
- start the script with the SHUTTER !
- wait until you see "press SET to save....."
- press FUNC/SET to store the badpixel.bin automatically in the right place

I can't seem to get the "press SET to save" message. I run the script as instructed, and the camera clearly is doing something, then some text flashes too fast to be read.

When I press PRINT, the display reads "Create badpixel.bin" in the bottom left corner, with ALT in the center at the bottom.

Can anyone tell me what I'm missing?

Logged

an0n

152

Re: the sx10 porting thread

« Reply #383 on: 20 / June / 2009, 23:11:49 »

Hi Sunflower,

Have you waited a while for message to appear, if so, check with File Browser to see if BADPIXEL.BIN is there, it should have 50kb - 60kb approx size. (Main Menu>Miscellaneous stuff>File Browser). If not then run through instructions again carefully, if it's there then DNG should be available.

Logged

A720IS.

fe50

3147
IXUS50 & 860, SX10 Star WARs-Star RAWs

Re: the sx10 porting thread

« Reply #384 on: 21 / June / 2009, 07:28:25 »

@Sunflower

Often the script output on the console get's overwriten (cleared) by the Canon OSD...

After the badpixel.lua script is started, it takes a first picture and calculates the bad pixels for ~ 10-15 seconds, then the blue print LED lits for ~ 3-5s; now a 2nd image is captured and calculated, takes 10-15s + 3-5s again...

After that the script is ready & shows the "press SET to save..." message...now (or better: let's say ~50 seconds after the script was started) just press FUNC/SET, regardless what you see on the LCD...

You can also press the <ALT> button twice to pause & continue the script, this refreshes the CHDK OSD and you'll see the messages on the console again...

Logged

-->FIRMWARE DUMPS<-- * Manual * Lua * me

marianoc

2

Re: the sx10 porting thread

« Reply #385 on: 21 / June / 2009, 09:58:35 »

thanks for all, porting sx10 1.02b.

very thanks,
mariano

---------------------

Muchas gracias a todos, por agregar la compativilidad de la sx10 1.02b.

un abrazo,
mariano

Logged

Sunflower

25

Re: the sx10 porting thread

« Reply #386 on: 21 / June / 2009, 19:36:05 »

Quote from: an0n on 20 / June / 2009, 23:11:49

Hi Sunflower,

Have you waited a while for message to appear, if so, check with File Browser to see if BADPIXEL.BIN is there, it should have 50kb - 60kb approx size. (Main Menu>Miscellaneous stuff>File Browser). If not then run through instructions again carefully, if it's there then DNG should be available.

It wasn't there.

Quote from: fe50 on 21 / June / 2009, 07:28:25

@Sunflower

Often the script output on the console get's overwriten (cleared) by the Canon OSD...

After the badpixel.lua script is started, it takes a first picture and calculates the bad pixels for ~ 10-15 seconds, then the blue print LED lits for ~ 3-5s; now a 2nd image is captured and calculated, takes 10-15s + 3-5s again...

After that the script is ready & shows the "press SET to save..." message...now (or better: let's say ~50 seconds after the script was started) just press FUNC/SET, regardless what you see on the LCD...

You can also press the <ALT> button twice to pause & continue the script, this refreshes the CHDK OSD and you'll see the messages on the console again...

The script was taking the pictures, but seemed to be hanging immediately after. FUNC/SET had no effect after three-four minutes.

I pressed the ALT button twice, then hit the shutter button. The script started again, and finished correctly. The BADPIXEL.BIN file now appears where it should be.

However, now when I power on the camera, and hit the ALT button, this script is loaded and ready to run again. Is there anyway I can unload the script?

Logged

fe50

3147
IXUS50 & 860, SX10 Star WARs-Star RAWs

Re: the sx10 porting thread

« Reply #387 on: 22 / June / 2009, 07:33:45 »

Quote from: Sunflower on 21 / June / 2009, 19:36:05

However, now when I power on the camera, and hit the ALT button, this script is loaded and ready to run again. Is there anyway I can unload the script?

CHDK always shows the last loaded/executet script; you can load the "default.bas" script to "unload" the script...

Logged

-->FIRMWARE DUMPS<-- * Manual * Lua * me

nimrod

33

1.01b port apparently booting now

« Reply #388 on: 22 / June / 2009, 09:10:41 »

Almost everyone is saying that the latest 1.01b test build is working! If you haven't tried it already, please give it a shot:

http://drop.io/nimrodfiles

If you're not yet familiar with how to get this to load, here's some information on how to create a bootable SD card:

http://chdk.wikia.com/wiki/Bootable_SD_card

Also see the FAQ:

http://chdk.wikia.com/wiki/FAQ

Q. How do I get CHDK onto my camera's SD memory card?
Q. How do I manually load CHDK so I can use it?

« Last Edit: 22 / June / 2009, 19:24:04 by nimrod »

Logged

beez

5

Re: the sx10 porting thread

« Reply #389 on: 22 / June / 2009, 17:37:54 »

Nimrod,

Downloaded the 1.01b and was able to load

I will do some more testing tomorrow

Thanks very much

Beez

Logged