Bug Reports against Recent Builds -- Report bugs here - page 25 - CHDK Releases - CHDK Forum  

Bug Reports against Recent Builds -- Report bugs here

  • 281 Replies
  • 75655 Views
*

Offline srsa_4c

  • ******
  • 3921
Re: Bug Reports against Recent Builds -- Report bugs here
« Reply #240 on: 05 / May / 2013, 10:36:08 »
Advertisements
The program that converted the .elf file to the .flt format was not handling 24 bit relative branch relocation properly. So the module would work if it got compiled with none of these relocations.

Phil.
Thanks for fixing this!
ARM CHDK now seems to run correctly.

Re: Bug Reports against Recent Builds -- Report bugs here
« Reply #241 on: 18 / August / 2013, 05:44:27 »
on the release sx130is-1.2.0-3031-full_beta when enabling video compression only the percent of compression appears on screen while capturing video
on older releases you could see the bitrate live on screen and it was very usefull. there is the option though on the video settings to show the live bitrate, i enable it but on the newer version it doesnt work.
there are other options to enable for onscreen help but none of the work as well

there is another bug as well on file browser. when by mistake u click on a file that isnt supposed to open doesnt simple ''doesnt open'' but freezes the camera after one minute by blank screen. after u click to open nothing happens you think ok nothing happened but after a minute screen goes black and it has nothing to do with automatic power save option since u cant revive the camera
« Last Edit: 18 / August / 2013, 05:52:28 by infin1te »

*

Offline philmoz

  • *****
  • 3107
    • Photos
Re: Bug Reports against Recent Builds -- Report bugs here
« Reply #242 on: 18 / August / 2013, 06:56:06 »
on the release sx130is-1.2.0-3031-full_beta when enabling video compression only the percent of compression appears on screen while capturing video
on older releases you could see the bitrate live on screen and it was very usefull. there is the option though on the video settings to show the live bitrate, i enable it but on the newer version it doesnt work.
there are other options to enable for onscreen help but none of the work as well

Should be fixed in version 3036 (trunk) and 3037 (release-1.2).

Quote
there is another bug as well on file browser. when by mistake u click on a file that isnt supposed to open doesnt simple ''doesnt open'' but freezes the camera after one minute by blank screen. after u click to open nothing happens you think ok nothing happened but after a minute screen goes black and it has nothing to do with automatic power save option since u cant revive the camera

I can't reproduce this - what was the file extension?
I'm assuming by 'click' you mean pressing the FUNC/SET button.

Phil.
CHDK ports:
  sx30is (1.00c, 1.00h, 1.00l, 1.00n & 1.00p)
  g12 (1.00c, 1.00e, 1.00f & 1.00g)
  sx130is (1.01d & 1.01f)
  ixus310hs (1.00a & 1.01a)
  sx40hs (1.00d, 1.00g & 1.00i)
  g1x (1.00e, 1.00f & 1.00g)

Re: Bug Reports against Recent Builds -- Report bugs here
« Reply #243 on: 18 / August / 2013, 07:02:48 »
Quote
there is another bug as well on file browser. when by mistake u click on a file that isnt supposed to open doesnt simple ''doesnt open'' but freezes the camera after one minute by blank screen. after u click to open nothing happens you think ok nothing happened but after a minute screen goes black and it has nothing to do with automatic power save option since u cant revive the camera

I can't reproduce this - what was the file extension?
I'm assuming by 'click' you mean pressing the FUNC/SET button.

Phil.
i cant reproduce it as well now. maby it was a random crash. thank you thank you for your reply and your script. you and all the developers!


S100 with CHDK (active or not) unable to make native RAW (CR2 or CRW)
« Reply #244 on: 09 / September / 2013, 02:03:43 »
When my S100 is booted with CHDK  s100-102a-1.2.0-3055-full_BETA
-If booted without CHDK, native RAW is named "CR2" and ~15MB
-When booted with CHDK - and asking for a DNG file - it works fine.

To reproduce problem, - uncheck DNG option in CHDK, try to make a CR2 or CRW file.
take a raw photo, - you will get a CRW og 19MB, that is unreadable by any application.
-same problem remains if ALT mode is disabled after boot.


Additional clue; creation of badpixel file fails every time - after taking 2 pictures.

Re: S100 with CHDK (active or not) unable to make native RAW (CR2 or CRW)
« Reply #245 on: 09 / September / 2013, 03:58:40 »
If booted without CHDK, native RAW is named "CR2" and ~15MB
This is normal for your camera model - it's the RAW file produced  by the Canon firmware.

Quote
When booted with CHDK - and asking for a DNG file - it works fine.
This is also normal for your camera - it's the DNG format file produced by CHDK.

Quote
To reproduce problem, - uncheck DNG option in CHDK, try to make a CR2 or CRW file.
take a raw photo, - you will get a CRW og 19MB, that is unreadable by any application.
-same problem remains if ALT mode is disabled after boot.
This is also normal for your camera.  In this case,  CHDK is saving a raw dump of your camera's sensor data.  You might want to read through this thread :

link> Questions about RAW ?

Quote
Additional clue; creation of badpixel file fails every time - after taking 2 pictures.
Unrelated problem.  Search the forum for "bad pixel create".
Ported :   A1200    SD940   G10    Powershot N    G16

*

Offline srsa_4c

  • ******
  • 3921
Re: Bug Reports against Recent Builds -- Report bugs here
« Reply #246 on: 27 / October / 2013, 08:35:59 »
I started seeing question marks on my older a4x0 cameras a while ago when half-pressing the shutter, but didn't pay much attention. I thought it was a porting problem.
Turns out it's changeset 3035 that broke the aperture display for CAM_DRAW_EXPOSITION cameras. Since multiple functions are involved in code that I don't know well, I'm filing this bug instead of trying to solve it myself. Sorry for not noticing this earlier.

edit: of course only cameras without a real iris are affected
« Last Edit: 27 / October / 2013, 15:42:27 by srsa_4c »

*

Offline philmoz

  • *****
  • 3107
    • Photos
Re: Bug Reports against Recent Builds -- Report bugs here
« Reply #247 on: 27 / October / 2013, 17:26:39 »
I started seeing question marks on my older a4x0 cameras a while ago when half-pressing the shutter, but didn't pay much attention. I thought it was a porting problem.
Turns out it's changeset 3035 that broke the aperture display for CAM_DRAW_EXPOSITION cameras. Since multiple functions are involved in code that I don't know well, I'm filing this bug instead of trying to solve it myself. Sorry for not noticing this earlier.

edit: of course only cameras without a real iris are affected

Attached version of shooting.c should fix it (I'm away from build system at the moment so I can't test this yet).

Phil.
CHDK ports:
  sx30is (1.00c, 1.00h, 1.00l, 1.00n & 1.00p)
  g12 (1.00c, 1.00e, 1.00f & 1.00g)
  sx130is (1.01d & 1.01f)
  ixus310hs (1.00a & 1.01a)
  sx40hs (1.00d, 1.00g & 1.00i)
  g1x (1.00e, 1.00f & 1.00g)


*

Offline srsa_4c

  • ******
  • 3921
Re: Bug Reports against Recent Builds -- Report bugs here
« Reply #248 on: 27 / October / 2013, 18:49:56 »
Attached version of shooting.c should fix it
The display is back, thanks.

Bug Reports against Recent Builds -- graphics display bug
« Reply #249 on: 03 / November / 2013, 09:49:45 »
Patch to fix graphics display bug described here :  http://chdk.setepontos.com/index.php?topic=10875

Works for both 1.2.0 & 1.3.0 branches.

Thanks to philmoz for making it easy to find and fix.

Note : original patch file posted at above thread was broken.  Corrected version now there and here.
« Last Edit: 03 / November / 2013, 09:51:24 by waterwingz »
Ported :   A1200    SD940   G10    Powershot N    G16

 

Related Topics