...the software although ported for firmware version G also seems to work (so far without any issues) on version F firmware.
Is it possible to downgrade the firmware from 1.00H to G or F?
// Camera - ixusizoom_sd30 - platform_camera.h// This file contains the various settings values specific to the ixusizoom_sd30 camera.// This file is referenced via the 'include/camera.h' file and should not be loaded directly.// If adding a new settings value put a suitable default in 'include/camera.h',// along with documentation on what the setting does and how to determine the correct value.// If the setting should not have a default value then add it in 'include/camera.h'// using the '#undef' directive along with appropriate documentation.// Override any default values with your camera specific values in this file. Try and avoid// having override values that are the same as the default value.// When overriding a setting value there are two cases:// 1. If removing the value, because it does not apply to your camera, use the '#undef' directive.// 2. If changing the value it is best to use an '#undef' directive to remove the default value// followed by a '#define' to set the new value.// When porting CHDK to a new camera, check the documentation in 'include/camera.h'// for information on each setting. If the default values are correct for your camera then// don't override them again in here. #define CAM_PROPSET 1 #define CAM_RAW_ROWPIX 2672 // for 5 MP #define CAM_RAW_ROWS 1968 // for 5 MP #undef CAM_USE_ZOOM_FOR_MF #undef CAM_HAS_ERASE_BUTTON #undef CAM_HAS_IRIS_DIAPHRAGM #define CAM_HAS_ND_FILTER 1 #undef CAM_HAS_MANUAL_FOCUS #undef CAM_HAS_USER_TV_MODES #define CAM_SHOW_OSD_IN_SHOOT_MENU 1 #undef CAM_HAS_IS //#define CAM_CONSOLE_LOG_ENABLED 1 #undef CAM_VIDEO_CONTROL // #define REMOTE_SYNC_STATUS_LED 0xC0xxyyyy // specifies an LED that turns on while camera waits for USB remote to sync // Keyboard repeat and initial delays #undef KBD_REPEAT_DELAY #define KBD_REPEAT_DELAY 140 #undef KBD_INITIAL_DELAY #define KBD_INITIAL_DELAY 300 // "real" to "market" conversion definitions #define SV96_MARKET_OFFSET 0 // market-real sv96 conversion value // Conversion values for 'no' conversion required // Uses integer arithmetic to avoid floating point calculations. Values choses to get as close // to the desired multiplication factor as possible within normal ISO range. #define ISO_MARKET_TO_REAL_MULT 2 #define ISO_MARKET_TO_REAL_SHIFT 1 #define ISO_MARKET_TO_REAL_ROUND 0 #define ISO_REAL_TO_MARKET_MULT 2 #define ISO_REAL_TO_MARKET_SHIFT 1 #define ISO_REAL_TO_MARKET_ROUND 0 //----------------------------------------------------------
I'm trying to compile all the cameras with CHDK shell, and the ixusizoom_SD30 stops the process with an error because CAM_ACTIVE_AREA_X1 is undefined. Would it be possible to add these cropping definitions, assuming they are correct? They are taken from a camera with the same sensor dimensions as the SD30. That is, #define CAM_RAW_ROWPIX 2672 // for 5 MP #define CAM_RAW_ROWS 1968 // for 5 MP // cropping #define CAM_JPEG_WIDTH 2592 #define CAM_JPEG_HEIGHT 1944 #define CAM_ACTIVE_AREA_X1 14 #define CAM_ACTIVE_AREA_Y1 10 #define CAM_ACTIVE_AREA_X2 2626 #define CAM_ACTIVE_AREA_Y2 1966This is the entire ixusizoom_sd30/platform_camera.hCode: [Select]// Camera - ixusizoom_sd30 - platform_camera.h// This file contains the various settings values specific to the ixusizoom_sd30 camera.// This file is referenced via the 'include/camera.h' file and should not be loaded directly.// If adding a new settings value put a suitable default in 'include/camera.h',// along with documentation on what the setting does and how to determine the correct value.// If the setting should not have a default value then add it in 'include/camera.h'// using the '#undef' directive along with appropriate documentation.// Override any default values with your camera specific values in this file. Try and avoid// having override values that are the same as the default value.// When overriding a setting value there are two cases:// 1. If removing the value, because it does not apply to your camera, use the '#undef' directive.// 2. If changing the value it is best to use an '#undef' directive to remove the default value// followed by a '#define' to set the new value.// When porting CHDK to a new camera, check the documentation in 'include/camera.h'// for information on each setting. If the default values are correct for your camera then// don't override them again in here. #define CAM_PROPSET 1 #define CAM_RAW_ROWPIX 2672 // for 5 MP #define CAM_RAW_ROWS 1968 // for 5 MP #undef CAM_USE_ZOOM_FOR_MF #undef CAM_HAS_ERASE_BUTTON #undef CAM_HAS_IRIS_DIAPHRAGM #define CAM_HAS_ND_FILTER 1 #undef CAM_HAS_MANUAL_FOCUS #undef CAM_HAS_USER_TV_MODES #define CAM_SHOW_OSD_IN_SHOOT_MENU 1 #undef CAM_HAS_IS //#define CAM_CONSOLE_LOG_ENABLED 1 #undef CAM_VIDEO_CONTROL // #define REMOTE_SYNC_STATUS_LED 0xC0xxyyyy // specifies an LED that turns on while camera waits for USB remote to sync // Keyboard repeat and initial delays #undef KBD_REPEAT_DELAY #define KBD_REPEAT_DELAY 140 #undef KBD_INITIAL_DELAY #define KBD_INITIAL_DELAY 300 // "real" to "market" conversion definitions #define SV96_MARKET_OFFSET 0 // market-real sv96 conversion value // Conversion values for 'no' conversion required // Uses integer arithmetic to avoid floating point calculations. Values choses to get as close // to the desired multiplication factor as possible within normal ISO range. #define ISO_MARKET_TO_REAL_MULT 2 #define ISO_MARKET_TO_REAL_SHIFT 1 #define ISO_MARKET_TO_REAL_ROUND 0 #define ISO_REAL_TO_MARKET_MULT 2 #define ISO_REAL_TO_MARKET_SHIFT 1 #define ISO_REAL_TO_MARKET_ROUND 0 //----------------------------------------------------------
This camera does not support RAW/DNG. Perhaps there is a problem with the extra code.
#if defined(CAM_ACTIVE_AREA_X1) && defined(CAM_JPEG_WIDTH) {{ (CAM_ACTIVE_AREA_X2-CAM_ACTIVE_AREA_X1-CAM_JPEG_WIDTH)/2, (CAM_ACTIVE_AREA_Y2-CAM_ACTIVE_AREA_Y1-CAM_JPEG_HEIGHT)/2, CAM_JPEG_WIDTH, CAM_JPEG_HEIGHT }}, { { CAM_ACTIVE_AREA_Y1, CAM_ACTIVE_AREA_X1, CAM_ACTIVE_AREA_Y2, CAM_ACTIVE_AREA_X2 } }, #else {{ 0, 0, 0, 0 }}, { { 0, 0, 0, 0 } }, #endif
Have dumped a SD-30_fw100e, to big to upload...
Started by fasdewx General Discussion and Assistance
Started by nycdesigner CHDK Releases
Started by beowulf226 Hello, I'm a NEWBIE - HELP!! (Newbies assistance, User Guides and thank you notes)
Started by ChaoZ General Discussion and Assistance
Started by CharlieM76 Firmware Dumping
