SX110IS - howto start porting - page 54 - DryOS Development - CHDK Forum supplierdeeply

SX110IS - howto start porting

  • 573 Replies
  • 236807 Views
Re: SX110IS - howto start porting
« Reply #530 on: 22 / November / 2009, 23:40:47 »
Advertisements
is a port of the curves to 12-bit under development at the moment? any word on current status, ETA? can i help? :-)

*

Offline jng

  • *
  • 6
Re: SX110IS - howto start porting
« Reply #531 on: 28 / November / 2009, 12:50:42 »

*

Offline chdkj

  • ***
  • 140
Re: SX110IS - howto start porting
« Reply #532 on: 29 / November / 2009, 12:24:21 »
Question: How to set custom camera profiles in Lightroom?

Put them into the camera profiles folder of Adobe Camera Raw (application data folder for "All Users"; for instance C:\Documents and Settings\All Users\AppData\Adobe\CameraRaw\CameraProfiles\Camera\Canon PowerShot SX110IS). Paths might be different at your setup.

Cheers.
sx110

Re: SX110IS - howto start porting
« Reply #533 on: 12 / December / 2009, 21:45:40 »
any word on development of curves for 12-bit sensors?


*

Offline chdkj

  • ***
  • 140
Re: SX110IS - howto start porting
« Reply #534 on: 13 / December / 2009, 13:00:44 »
I don't track that. It's not a camera specific issue. You should search for in forum.
sx110

Re: SX110IS - howto start porting
« Reply #535 on: 25 / January / 2010, 09:38:55 »
Thank you !!! chdkj and everyone on the chdk development - even other builds - currently using sx110 used s5is s3is s2is .

*

Offline hotvedt

  • ***
  • 106
  • A540/SX110IS/350D
Re: SX110IS - howto start porting
« Reply #536 on: 21 / April / 2010, 19:59:59 »
Hello, I just got an sx110is and have a question/request:



When i use dcraw on the dng's produced by the camera, i get a quite much bigger image than from acr on the same file, or
from the jpeg.
Would it be possible to change the dng-code so acr doesn't crop this much?  I think a little more than 1 megapixel is being cropped away.
Or is it a good reason for cropping this much?

*

Offline whoever

  • ****
  • 280
  • IXUS950
Re: SX110IS - howto start porting
« Reply #537 on: 22 / April / 2010, 03:59:10 »
Try Thomas Knoll's utility DNG Recover Edges. It is supposed to reset DefaultCropOrigin and DefaultCropSize tags in the DNG header to match the whole active area of the sensor.


*

Offline hotvedt

  • ***
  • 106
  • A540/SX110IS/350D
Re: SX110IS - howto start porting
« Reply #538 on: 22 / April / 2010, 08:08:45 »
Thank you! It seems to work perfectly.  :D



Also works on dng's from A540 and 350D, but not so much to gain there, as in the SX110IS.

*

Offline chdkj

  • ***
  • 140
Re: SX110IS - howto start porting
« Reply #539 on: 22 / April / 2010, 16:41:27 »
Interesting...

Why does ACR cuts pixels off and DCRAW does not? Is there any need to change/fix some code in CHDK for SX110 regarding this issue?
sx110

 

Related Topics


SimplePortal 2.3.6 © 2008-2014, SimplePortal