G11 porting - page 7 - DryOS Development - CHDK Forum  
« previous next »
Pages: 1 2 3 4 5 6 [7] 8 9 10 11 12 ... 54   Go Down

G11 porting

  • 530 Replies
  • 245517 Views
*

Offline Microfunguy

  • ****
  • 4037
    • StereoData Maker
Re: G11 porting
« Reply #60 on: 28 / December / 2009, 11:52:46 »
Advertisements
These are custom connectors made especially for the Ipod.

You need to obtain a 3.5mm stereo jack plug.

Logged
*

Offline kingcang

  • **
  • 61
Re: G11 porting
« Reply #61 on: 28 / December / 2009, 12:18:56 »
« Last Edit: 28 / December / 2009, 13:05:32 by kingcang »
Logged
*

Offline Microfunguy

  • ****
  • 4037
    • StereoData Maker
Re: G11 porting
« Reply #62 on: 28 / December / 2009, 12:41:39 »
The link you posted is not relevant to your plug and cable.

It is impossible to tell from the photo in reply #34 which wire is connected to second ring.

Is it the yellow wire or the other wire (not sure what colour it is) ?

The image in above reply is not clear enough to tell.

Can you post a better image ?

The microphone input is connected to ground.
Logged
*

Offline kingcang

  • **
  • 61
Re: G11 porting
« Reply #63 on: 28 / December / 2009, 13:02:56 »
« Last Edit: 28 / December / 2009, 13:08:55 by kingcang »
Logged
*

Offline Microfunguy

  • ****
  • 4037
    • StereoData Maker
Re: G11 porting
« Reply #64 on: 28 / December / 2009, 13:11:38 »
I assume that both the yellow and red/green wire are connected to shield (ground) ?

Do you have a testmeter ?

If not, no futher progress can be made.
Logged
*

Offline sandeman

  • *
  • 31
Re: G11 porting
« Reply #65 on: 28 / December / 2009, 13:20:54 »
Quote from: Microfunguy on 28 / December / 2009, 13:11:38
I assume that both the yellow and red/green wire are connected to shield (ground) ?

Do you have a testmeter ?

If not, no futher progress can be made.
You can also improvise. E.g. by using a battery and small light bulb or LED.
Logged
*

Offline kingcang

  • **
  • 61
Re: G11 porting
« Reply #66 on: 28 / December / 2009, 13:23:48 »
« Last Edit: 28 / December / 2009, 13:28:48 by kingcang »
Logged
*

Offline Microfunguy

  • ****
  • 4037
    • StereoData Maker
Re: G11 porting
« Reply #67 on: 28 / December / 2009, 13:25:11 »
Quote from: sandeman on 28 / December / 2009, 13:20:54
You can also improvise. E.g. by using a battery and small light bulb or LED.

Yes, for determining how the wires are connected.

But we also need to see if there is a voltage on either of the microphone inputs on the sound card.

If there is, the phototransistor can simply connect that input to ground.

If not, we need to use an external battery.

Logged
*

Offline Microfunguy

  • ****
  • 4037
    • StereoData Maker
Re: G11 porting
« Reply #68 on: 28 / December / 2009, 13:35:36 »
So, do you have a test meter ?

If not, connect the jack plug to your sound card and run a free 'sound card oscilloscope' programme that will display the voltage.

Connect the red or green wire to the ground wires (make sure the insulation is removed from the wires).

Does the displayed signal voltage change ?


(It is easier to buy a very inexpensive Chinese-made testmeter).


Are you sure the microphone input of your sound card uses a stereo plug ?

It is more likely to be a mono jack plug.
« Last Edit: 28 / December / 2009, 14:08:41 by Microfunguy »
Logged
*

Offline kingcang

  • **
  • 61
Re: G11 porting
« Reply #69 on: 28 / December / 2009, 15:20:07 »
« Last Edit: 28 / December / 2009, 15:22:02 by kingcang »
Logged
Pages: 1 2 3 4 5 6 [7] 8 9 10 11 12 ... 54   Go Up
« previous next »
 

Related Topics
SimplePortal 2.3.6 © 2008-2014, SimplePortal