SDM 1.83 Release - page 3 - Microfunguy's Builds - CHDK Forum
« previous next »
Pages: 1 2 [3]   Go Down

SDM 1.83 Release

  • 27 Replies
  • 13036 Views
*

Offline hwntw

  • ***
  • 159
Re: SDM 1.83 Release
« Reply #20 on: 24 / June / 2010, 05:07:41 »
Advertisements
May I suggest a small change to SDM, concerning the zebra display?
Zebra shows as a single red colour, for both over- and under-exposure.
In CHDK I have set these as different colours, using a dull yellow for under-exposure. Can I change this somewhere in the SDM source code and recompile?
Logged
Ixus 300HS S100


Windows 10
*

Offline Microfunguy

  • ****
  • 4037
    • StereoData Maker
Re: SDM 1.83 Release
« Reply #21 on: 24 / June / 2010, 05:43:49 »
Quote from: hwntw on 24 / June / 2010, 05:07:41
Zebra shows as a single red colour, for both over- and under-exposure.

I was not aware of that, I will check it out.
I am busy with other tasks but will post link to a test build here when available.

Which firmware version is your G9 ?
Logged
*

Offline hwntw

  • ***
  • 159
Re: SDM 1.83 Release
« Reply #22 on: 24 / June / 2010, 06:07:44 »
Hello MFG,
My G9 build is d.
Logged
Ixus 300HS S100


Windows 10
*

Offline Microfunguy

  • ****
  • 4037
    • StereoData Maker
Re: SDM 1.83 Release
« Reply #23 on: 24 / June / 2010, 08:44:58 »
Here you are, try this  :-

http://www.zshare.net/download/77577886e1446d81/

Incidentally, display of near and far distance values is not related to hyperfocal .. it is for the rangefinder feature.
Logged
*

Offline hwntw

  • ***
  • 159
Re: SDM 1.83 Release
« Reply #24 on: 24 / June / 2010, 12:32:52 »
Ah, yes- how does the rangefinder feature work? Is it a script?
TVM for the build, spot on. I have red for over- and yellow for under-exposure.
Logged
Ixus 300HS S100


Windows 10
*

Offline Microfunguy

  • ****
  • 4037
    • StereoData Maker
Re: SDM 1.83 Release
« Reply #25 on: 24 / June / 2010, 12:34:38 »
I will tell you after I have finished painting the ceiling   :)
Logged
*

Offline Microfunguy

  • ****
  • 4037
    • StereoData Maker
Re: SDM 1.83 Release
« Reply #26 on: 25 / June / 2010, 05:22:43 »
Try following these instructions and see if it works OK  :-

http://stereo.jpn.org/eng/sdm/single.htm

Logged
*

Offline hwntw

  • ***
  • 159
Re: SDM 1.83 Release
« Reply #27 on: 17 / July / 2010, 18:05:43 »
Quote
TVM for the build, spot on. I have red for over- and yellow for under-exposure.

Hello again, I have switched to firmware version 100-i for my G9. Is there a chance of you copying me a build of SDM 1.84 for the corresponding firmware, 100-i, as before?
Logged
Ixus 300HS S100


Windows 10
Pages: 1 2 [3]   Go Up
« previous next »
 

Related Topics
SimplePortal 2.3.6 © 2008-2014, SimplePortal