IXUS 130 (SD1400 IS) Porting Thread - page 26 - DryOS Development - CHDK Forum supplierdeeply
« previous next »
Pages: 1 ... 21 22 23 24 25 [26] 27 28 29   Go Down

IXUS 130 (SD1400 IS) Porting Thread

  • 288 Replies
  • 117246 Views
*

Offline waterwingz

  • ******
  • 12128
    • Waterwingz
Re: IXUS 130 (SD1400 IS) Porting Thread
« Reply #250 on: 24 / September / 2012, 18:00:31 »
Advertisements
Quote from: jhjonsson on 24 / September / 2012, 17:46:08
However, I can't find my old SD-cards (perhaps I shipped them with the old cameras?) and the two cards I use in my IXUS 130 IS don't work in the card readers I have. I will get back here as soon as I either find one of those old cards or I get time to buy a new card reader. Very annoying.
If you send me a real email address via PM,  I'll send you a link to a CHDK version with instructions on how to format the card in your camera.

Logged
Ported :   A1200    SD940   G10    Powershot N    G16
*

Offline jhjonsson

  • *
  • 6
Re: IXUS 130 (SD1400 IS) Porting Thread
« Reply #251 on: 26 / September / 2012, 09:41:03 »
Got the card reader and have transfered the files - and prepared them (removed resource forks since I'm using a mac).

Works fine, as far as I can tell!  :)

I can both do single boots via the "firmware update" option in the camera as well as boot from a card that has been made bootable.

The only problem I've had is actually the instruction, which seems generic and a bit outdated:

The part describing how to verify the firmware version by pressing buttons does not mention that there is a crucial time limit. If you do not press "DISP" sufficiently fast after "FUNC SET", you only get the current time in the camera. You must hurry up.

When CHDK is being loaded, the "playback" button does not flash; there is a small LED next to it that flashes. Moreover, the camera starts up in playback mode after the CHDK Splash-Screen has been shown. It does not show the new battery-meter icon and "several other things". You only get to see this once the camera goes over to shooting mode.

It could be clear about what the "Shortcut" button is (the "button labeled "DISP").

"Make Card Bootable..." is not found on the submenu "Debug Parameters" (there is no such) but "Miscellaneous Stuff".

But after I had figured out this, and some other small issues, it all seems to work fine!
Logged
*

Offline waterwingz

  • ******
  • 12128
    • Waterwingz
Re: IXUS 130 (SD1400 IS) Porting Thread
« Reply #252 on: 26 / September / 2012, 10:21:22 »
Quote from: jhjonsson on 26 / September / 2012, 09:41:03
The only problem I've had is actually the instruction, which seems generic and a bit outdated:
I'm working on a rewrite of the included readme.txt file - it's included with every camera version of CHDK and needs to be very generic.   As you noticed, its also very out-of-date.  The new version will probably just point to the appropriate wiki pages rather than try to repeat the latest information on the wiki.

Quote
Moreover, the camera starts up in playback mode after the CHDK Splash-Screen has been shown.
Normal for CHDK.  If you want to start in shooting mode,  hold the On/Off button down when you start the camera until you hear the lens start to extend.


Quote
It does not show the new battery-meter icon and "several other things". You only get to see this once the camera goes over to shooting mode.
This is now a setup option that is configurable in the OSD menu..


Quote
It could be clear about what the "Shortcut" button is (the "button labeled "DISP").
The "Shortcut" or <ALT> button changes from camera to camera.  All depends on which button the person who ported the camera picked.   We've tried to standardize on the "Playback" button recently but that has not made its way into all camera - although its now user configurable in many of them.

Quote
"Make Card Bootable..." is not found on the submenu "Debug Parameters" (there is no such) but "Miscellaneous Stuff".
The menu systems was reworked in version 1.2.0 but the documentation is all still written around 1.1.0.   This will likely take some time to fix.
Logged
Ported :   A1200    SD940   G10    Powershot N    G16
*

Offline jhjonsson

  • *
  • 6
Re: IXUS 130 (SD1400 IS) Porting Thread
« Reply #253 on: 27 / September / 2012, 17:35:23 »
I have now tried beta 2 out to some degree and it seems to work fine. I'm not a professional photographer, though.

Sad to say, I have discovered a hardware problem with my camera. The camera has problems focusing, probably because an E18 ZoomLensError seem to have occurred a while ago.  :( I wasn't aware of this error but it could explain why many of the pictures now are not really as sharp and crisp as they were when the camera was new. It also means I'm not really sure if my tests are worth anything.
Logged
*

Offline waterwingz

  • ******
  • 12128
    • Waterwingz
Re: IXUS 130 (SD1400 IS) Porting Thread - Success
« Reply #254 on: 04 / October / 2012, 09:02:55 »
I've posted the beta 2 code for inclusion in the svn repository and promoted the 1.00C release to "alpha" status to be included in the autobuild.   All four beta testers have reported good results - dual partition booting now works properly and the only current bug is the "video zoom locks in digital mode" that is common on many cameras.

The 1.00A code has been updated but will not be available from the autobuild until somebody actually volunteers to test it.

Right now, (2012/10.04)  it looks like things are backed up with code submissions.  One svn maintainer is away on vacation and another backed up at work so it might be a while until you actually see this on the download page.

 
Logged
Ported :   A1200    SD940   G10    Powershot N    G16
*

Offline zestoi

  • *
  • 24
Re: IXUS 130 (SD1400 IS) Porting Thread
« Reply #255 on: 04 / October / 2012, 10:21:00 »
thanks for your hard work in getting this camera included in the main autobuilds. i really appreciate it :)
Logged
*

Offline durval

  • *
  • 3
Re: IXUS 130 (SD1400 IS) Porting Thread
« Reply #256 on: 06 / December / 2012, 07:51:39 »
Hi,

Quote from: zestoi on 04 / October / 2012, 10:21:00
thanks for your hard work in getting this camera included in the main autobuilds. i really appreciate it :)

I would like to second this and add my thanks as well. Waterwingz, you rock!

I've just downloaded the 1-2-0-2344-0 version and installed it in my SD1400IS via the "firmware upgrade" method, and it seems to be working alright. It's very nice being able to record DNG raw files with such a low-priced camera!

Just two questions:
1) After the upgrade, I've been getting intermitent "Memory card error" messages when turning it on, even before reloading CHDK. Some googling seems to indicate that this problem can sometimes be due to firmware (although I saw no mention of CHDK specifically). Usually removing the SD card and reinserting it "cures" the problem, although once I just removed the battery, counted to 10 and reinserted it, and the problem went away too. Is there anyone else getting this error?

2) The review screen is always locked in the "partial view" format, and of course I can't change it as the DISP key is now the CHDK macro key (even when I'm in review  mode). See attachment. Is that normal?

Cheers,
--
   Durval.
Logged
*

Offline waterwingz

  • ******
  • 12128
    • Waterwingz
Re: IXUS 130 (SD1400 IS) Porting Thread
« Reply #257 on: 06 / December / 2012, 09:12:58 »
Quote from: durval on 06 / December / 2012, 07:51:39
Just two questions:
1) After the upgrade, I've been getting intermitent "Memory card error" messages when turning it on, even before reloading CHDK. Some googling seems to indicate that this problem can sometimes be due to firmware (although I saw no mention of CHDK specifically). Usually removing the SD card and reinserting it "cures" the problem, although once I just removed the battery, counted to 10 and reinserted it, and the problem went away too. Is there anyone else getting this error?
Did you try using a different memory card ?

Quote
2) The review screen is always locked in the "partial view" format, and of course I can't change it as the DISP key is now the CHDK macro key (even when I'm in review  mode). See attachment. Is that normal?
Hold the DISP button down for more than one second (while not in <ALT> mode) and it should toggle through the display modes.
Logged
Ported :   A1200    SD940   G10    Powershot N    G16
*

Offline zestoi

  • *
  • 24
Re: IXUS 130 (SD1400 IS) Porting Thread
« Reply #258 on: 06 / December / 2012, 10:11:34 »
Quote from: durval on 06 / December / 2012, 07:51:39
I've just downloaded the 1-2-0-2344-0 version and installed it in my SD1400IS via the "firmware upgrade" method, and it seems to be working alright. It's very nice being able to record DNG raw files with such a low-priced camera!

certainly packs a lot of functionality now into a very small device  :D

Quote from: waterwingz on 06 / December / 2012, 09:12:58
Hold the DISP button down for more than one second (while not in <ALT> mode) and it should toggle through the display modes.

that works fine here
Logged
*

Offline durval

  • *
  • 3
Re: IXUS 130 (SD1400 IS) Porting Thread
« Reply #259 on: 08 / December / 2012, 11:13:14 »
Hi Waterwingz,

Sorry for the delay; I've turned on "notify" for this forum post, but GMail trashed the notifications to my spam box; just found them there.

Quote from: waterwingz on 06 / December / 2012, 09:12:58
Quote from: durval on 06 / December / 2012, 07:51:39
Just two questions:
1) After the upgrade, I've been getting intermitent "Memory card error" messages when turning it on, even before reloading CHDK. Some googling seems to indicate that this problem can sometimes be due to firmware (although I saw no mention of CHDK specifically). Usually removing the SD card and reinserting it "cures" the problem, although once I just removed the battery, counted to 10 and reinserted it, and the problem went away too. Is there anyone else getting this error?
Did you try using a different memory card ?
Quote

Yep, replaced my 32GB SDHC with an 8GB SDHC and did not have any issues since. Probably it was a bad card, then...

2) The review screen is always locked in the "partial view" format, and of course I can't change it as the DISP key is now the CHDK macro key (even when I'm in review  mode). See attachment. Is that normal?
Hold the DISP button down for more than one second (while not in <ALT> mode) and it should toggle through the display modes.

Perfect. Thanks for the pointer, and I think it's high time I RTFM the fine CHDK manual... :-)

Cheers,
--
   Durval.
Logged
Pages: 1 ... 21 22 23 24 25 [26] 27 28 29   Go Up
« previous next »
 

Related Topics