A495 porting thread - page 13 - DryOS Development - CHDK Forum supplierdeeply

A495 porting thread

  • 346 Replies
  • 114219 Views
Re: A495 porting thread
« Reply #120 on: 30 / May / 2011, 14:55:18 »
Advertisements

Only one light lights.

The green led flashes and stops when the camera hangs.
The Autofocus light (on the front of the camera) does not come on at all ?
Ported :   A1200    SD940   G10    Powershot N    G16

Re: A495 porting thread
« Reply #121 on: 30 / May / 2011, 15:01:54 »
Stop my_kbd_read_keys() calling kbd_process(), all sorts of exciting things happen there.

Re: A495 porting thread
« Reply #122 on: 30 / May / 2011, 15:10:23 »
no , the autofocus light stays quiet

Re: A495 porting thread
« Reply #123 on: 30 / May / 2011, 15:15:25 »
No ! Autofocus is tunred on !

I actualy testing - I caome back in a few minutes


Re: A495 porting thread
« Reply #124 on: 30 / May / 2011, 15:16:07 »
no , the autofocus light stays quiet
Hmmm .... address on the wiki page must be wrong.

I assume the green LED blink you reported seeing does not happen during a normal camera starup ?

Okay then - lets try this.  I moved the LED code into the keyboard task - lets see if it still lights up.

http://www.box.net/shared/fqbq8nkhao

I also took microfunguy's suggestion to kill the kbd_process().

Ported :   A1200    SD940   G10    Powershot N    G16

Re: A495 porting thread
« Reply #125 on: 30 / May / 2011, 15:21:34 »
Ok - the cam boots with flickering the green led only until the chdk logo appears.

The autofokus-led is on from start => Crash continious on.

Thems to be good

Re: A495 porting thread
« Reply #126 on: 30 / May / 2011, 15:31:48 »
In normal boot (no chdk) the green light flashes too but the motors opens the optics. In both cases the light flashes five times.

I see no light in front side.

Re: A495 porting thread
« Reply #127 on: 30 / May / 2011, 15:34:31 »
Using this as an example, comment-out lines 170 to 190 :-

http://tools.assembla.com/chdk/browser/trunk/core/main.c

See if the folders were created.

Also comment-out 136, conf_restore().
« Last Edit: 30 / May / 2011, 15:38:58 by Microfunguy »


Re: A495 porting thread
« Reply #128 on: 30 / May / 2011, 15:45:35 »
In normal boot (no chdk) the green light flashes too but the motors opens the optics. In both cases the light flashes five times.

I see no light in front side.

On my cam the green light blinks until chdk seems to start up. Then the light is out.
The red autofocus-LED is permanently on.

Re: A495 porting thread
« Reply #129 on: 30 / May / 2011, 15:50:31 »
Using this as an example, comment-out lines 170 to 190 :-
Also comment-out 136, conf_restore().
In my original SD940 port,  I had code in the spytask that blinked the green LED every so often.  Its quite possible  spytask is still running after the "crash"  would be interesting to know.  I think that's kind of what you are looking for ?


Ok - the cam boots with flickering the green led only until the chdk logo appears.

The autofokus-led is on from start => Crash continious on.
In normal boot (no chdk) the green light flashes too but the motors opens the optics. In both cases the light flashes five times.

I see no light in front side.
As the A495 has only one LED (the green one) and its used by lots of things,  its not going to be much help for debugging.   Too bad astrosalva's AF led does not work - and strange that HankeyPoo's does.   

Ported :   A1200    SD940   G10    Powershot N    G16

 

Related Topics


SimplePortal 2.3.6 © 2008-2014, SimplePortal