A3000IS poring thread - page 12 - DryOS Development - CHDK Forum supplierdeeply

A3000IS poring thread

  • 142 Replies
  • 29573 Views
Re: A3000IS poring thread
« Reply #110 on: 30 / December / 2018, 19:16:37 »
Advertisements
@reyalp, this one worked.  The kap_uav.lua script runs perfectly now.  Thank you again for troubleshooting this and proving a fix. Cheers!

*

Offline reyalp

  • ******
  • 11853
Re: A3000IS poring thread
« Reply #111 on: 30 / December / 2018, 20:10:53 »
@reyalp, this one worked.  The kap_uav.lua script runs perfectly now.  Thank you again for troubleshooting this and proving a fix. Cheers!
Thanks for reporting the issue and confirming the fix.

The change is checked in and will be in CHDK  1.4 and 1.5 autobuilds 5145 and later for all A3000 firmware versions.
Don't forget what the H stands for.

*

Offline srsa_4c

  • ******
  • 3881
Re: A3000IS poring thread
« Reply #112 on: 10 / January / 2019, 18:32:35 »
Test build with the following changes:
- adjustments in capt_seq.c to match ixus120_sd940
- new loader and compat check enabled

Expected result: it boots and passes hooktest.lua
I hope I have not screwed up something.

Re: A3000IS poring thread
« Reply #113 on: 10 / January / 2019, 19:18:40 »
@srsa_4c, here is the log file from running the hooktest.lua using your build.  It still seems to fail.  Same behavior with the kap_uav.lua script as well?
« Last Edit: 10 / January / 2019, 19:29:39 by cagiva »


*

Offline srsa_4c

  • ******
  • 3881
Re: A3000IS poring thread
« Reply #114 on: 11 / January / 2019, 11:57:39 »
@srsa_4c, here is the log file from running the hooktest.lua using your build.  It still seems to fail.
Indeed, it fails the same way.
Re-install the official release on your card, and run the attached script. It's the same hooktest script, but I replaced all keypress/release commands with keypress events. I'm curious whether you get different results.

Re: A3000IS poring thread
« Reply #115 on: 11 / January / 2019, 12:52:01 »
@srsa_4c
Attached the log.  Thanks again for taking the time to look into this.

*

Offline srsa_4c

  • ******
  • 3881
Re: A3000IS poring thread
« Reply #116 on: 11 / January / 2019, 13:13:53 »
This is getting really odd. The failures remain, only 3 shots are made instead of 5.
To rule out a camera setting causing trouble, try resetting the camera to defaults using the Canon menu.
Afterwards, please enable continuous shooting mode on the Canon interface (I don't know how to do it on your cam), and re-run the script. That will enable the script to do a test in continuous mode too. In case you have flash enabled, disable it. Also disable any sort of continuous AF or servo AF or face AF in the Canon menu.

Anyone else have an idea what could cause this?

Re: A3000IS poring thread
« Reply #117 on: 11 / January / 2019, 15:24:26 »
@srsa_4c
I reset the camera to the Canon default settings and set the following settings:

AF Frame - Center
AF Frame size - Normal
Digital zoom - Off
AF Point zoom - Off
AF-Assist Beam - Off
Continuous AF - Off
IS Mode - Off
Flash Setting:
Red-Eye Corr. - Off
Red-Eye Lamp - On


Unfortunately, the failure still persists.

Luckly, I have another A3000IS camera.  However, it came with the 100c firmware version.  With this one, your script passes successfully (see both attached log files).


Re: A3000IS poring thread
« Reply #118 on: 11 / January / 2019, 15:26:16 »
Unfortunately, I still get the extra LED pulse on Burst mode and a very long (~1.3s) single one in Fast mode; when I run @waterwingz  KAP script on the second camera as well (log files attached).

*

Offline srsa_4c

  • ******
  • 3881
Re: A3000IS poring thread
« Reply #119 on: 11 / January / 2019, 17:40:16 »
Unfortunately, the failure still persists.
Have you been using the same SD card in the 100d camera for all tests so far? Can you try a different card?

 

Related Topics