A2200 IS porting thread - page 43 - DryOS Development - CHDK Forum
« previous next »
Pages: 1 ... 38 39 40 41 42 [43] 44 45 46 47 48 ... 52   Go Down

A2200 IS porting thread

  • 515 Replies
  • 198767 Views
*

Offline cqui

  • *
  • 5
Re: A2200 IS porting thread
« Reply #420 on: 27 / July / 2012, 05:39:13 »
Advertisements
Quote from: waterwingz on 26 / July / 2012, 18:05:01
Quote from: cqui on 26 / July / 2012, 05:33:06
Another question, where can I signal to the EOScard team that there might be an issue there
Were you using the most recent version :
http://chdk.wikia.com/wiki/EOScard ?
The screenshots there seem to show it working properly.
I tried again,
* first with the card I manually corected, it now shows the correct address,
* then with another card that has not been tagged yet and it shows the wrong address 0x05c.
I think, to reproduce the issue, insert a card than has never been tagged (or where the BOOTDISK tag has been "blanked"?), formated to FAT32 and run EOScard.

I have a sceren shot, done with a fresh download, on a FAT32 card that has never been tagged, should I post it? Where?
Logged
*

Offline Matthayichen

  • *
  • 11
Re: A2200 IS porting thread
« Reply #421 on: 27 / July / 2012, 07:46:59 »
One question: Is the UI as flickery and evanescent on other cameras as well, or is it fixable but no one's gotten around to it?
Logged
*

Offline cqui

  • *
  • 5
Re: A2200 IS porting thread
« Reply #422 on: 27 / July / 2012, 13:50:51 »
Quote from: Matthayichen on 27 / July / 2012, 07:46:59
One question: Is the UI as flickery and evanescent on other cameras as well, or is it fixable but no one's gotten around to it?
Up to now I have not seen anything flickering,
I have a 1.00d firmware version, and you?
Is it only in specific menu/operations or random or always?
Logged
*

Offline Nilinhim

  • ***
  • 127
Re: A2200 IS porting thread
« Reply #423 on: 29 / July / 2012, 10:27:39 »
Just for fun!

Some of the things I was able to do with this camera and CHDK:

Night photography: link & link
Light painting: link
Lightning photography: link
Transit of Venus: link
3D photography: link & link
Logged
*

Offline reyalp

  • ******
  • 14128
Re: A2200 IS porting thread
« Reply #424 on: 29 / July / 2012, 15:51:32 »
Quote from: cqui on 27 / July / 2012, 13:50:51
Quote from: Matthayichen on 27 / July / 2012, 07:46:59
One question: Is the UI as flickery and evanescent on other cameras as well, or is it fixable but no one's gotten around to it?
Up to now I have not seen anything flickering,
I have a 1.00d firmware version, and you?
Is it only in specific menu/operations or random or always?
Some flicker is normal when the canon OSD updates. This depends on your shooting settings, for example if you have face detect on, it will update a lot more frequently to draw the face boxes.
Logged
Don't forget what the H stands for.
*

Offline kmnfive

  • *
  • 6
Re: A2200 IS porting thread
« Reply #425 on: 03 / August / 2012, 02:53:57 »
I'm having issues loading the CHDK.....

I have 1.00d, a2200, i used eoscard (the latest version linked above) and wrote bootdisk on the sector, it's a 16gb transcend card, i unzipped all the files onto the sd card, how do i access the CHDK menu?

am i supposed to see a splash screen?

Logged
*

Offline waterwingz

  • ******
  • 12140
    • Waterwingz
Re: A2200 IS porting thread
« Reply #426 on: 03 / August / 2012, 10:14:21 »
Quote from: kmnfive on 03 / August / 2012, 02:53:57
I have 1.00d, a2200, i used eoscard (the latest version linked above) and wrote bootdisk on the sector, it's a 16gb transcend card, i unzipped all the files onto the sd card, how do i access the CHDK menu?
Questions :
1) Is the card formatted FAT32 (not exFAT)?
2) Did EOScard write BOOTDISK at 0x1E0?
3) Are you using a PC or a MAC ?
4) Did you remember to move the SD card lock switch to the locked position ?

Quote
am i supposed to see a splash screen?
Yes

Update :  from the first post in this thread "To enter CHDK <Alt> mode use the FACE button."
« Last Edit: 03 / August / 2012, 10:25:24 by waterwingz »
Logged
Ported :   A1200    SD940   G10    Powershot N    G16
*

Offline kmnfive

  • *
  • 6
Re: A2200 IS porting thread
« Reply #427 on: 03 / August / 2012, 21:06:34 »
Quote from: waterwingz on 03 / August / 2012, 10:14:21
Quote from: kmnfive on 03 / August / 2012, 02:53:57
I have 1.00d, a2200, i used eoscard (the latest version linked above) and wrote bootdisk on the sector, it's a 16gb transcend card, i unzipped all the files onto the sd card, how do i access the CHDK menu?
Questions :
1) Is the card formatted FAT32 (not exFAT)?
2) Did EOScard write BOOTDISK at 0x1E0?
3) Are you using a PC or a MAC ?
4) Did you remember to move the SD card lock switch to the locked position ?

Quote
am i supposed to see a splash screen?
Yes

Update :  from the first post in this thread "To enter CHDK <Alt> mode use the FACE button."

It came formatted as fat32, should i reformat?

also, how do i know if it wrote BOOTDISK on that sector at 0x1E0? through a hex editor? is there any other way to verify?

I'm on PC. Yes i put it on locked.
Logged
*

Offline henriquedt

  • *
  • 3
Re: A2200 IS porting thread
« Reply #428 on: 03 / August / 2012, 21:24:13 »
Hello Everyone.
Im new to CHDK. everything went fine with my installation, which i made through this step-by-step tutorial: http://komku.blogspot.com.br/2010/05/how-to-install-chdk-on-canon-digital.html

I have some questions about the last build (1984), which is the first one i installed.
I can now set manual Shutter Speed, however, the ISO Speed shown on the camera when i half press the shutter and/or after i take the picture, even on the EXIF, is not matching with the ISO Speed set on CHDK.
By an example, when i want ISO 1000 i put ISO Value 100/Factor 10 or the reverse and it gives me ISO 1600 or even higher. Is everyone experiencing the same problem?

Also, another question, this camera takes max 1.0fps on P - Program mode, but it takes 3+ FPS when on Low Light or Blur Reduction SCN Mode (Everyone Knows that, Ok, Sorry).  I would like to know if it is possible to make the camera take 3FPS on the P Mode, with full resolution. I really don't have any idea on how to make this happen, however, with CHDK i can always go higher than ISO 1600 on P Mode, and this was impossible with the default camera software.

Thanks to everyone who contributed to this project, im really happy with the new possibilities that CHDK opened to my camera :)
Logged
*

Offline reyalp

  • ******
  • 14128
Re: A2200 IS porting thread
« Reply #429 on: 03 / August / 2012, 21:35:17 »
Quote from: henriquedt on 03 / August / 2012, 21:24:13
I have some questions about the last build (1984), which is the first one i installed.
I can now set manual Shutter Speed, however, the ISO Speed shown on the camera when i half press the shutter and/or after i take the picture, even on the EXIF, is not matching with the ISO Speed set on CHDK.
The displayed ISO value and the override value are not the same, see discussion of "market" and "real" ISO on http://chdk.wikia.com/wiki/CHDK_User_Manual#Override_ISO_value

It is also possible the camera display and exif may do not reflect the actual value used. You should compare the actual brightness of the images if you want to be sure if the override is working or not.

Quote
Also, another question, this camera takes max 1.0fps on P - Program mode, but it takes 3+ FPS when on Low Light or Blur Reduction SCN Mode (Everyone Knows that, Ok, Sorry).  I would like to know if it is possible to make the camera take 3FPS on the P Mode, with full resolution.
No. These modes are fast because the image resolution is reduced very early in the canon processing. If Canon could make their camera shoot 3x faster at full quality, they would already do that.
Logged
Don't forget what the H stands for.
Pages: 1 ... 38 39 40 41 42 [43] 44 45 46 47 48 ... 52   Go Up
« previous next »
 

Related Topics


SimplePortal © 2008-2014, SimplePortal