Adding new cameras, applying patches into trunk (with source code prepared) - page 159 - General Discussion and Assistance - CHDK Forum
supplierdeeply

Adding new cameras, applying patches into trunk (with source code prepared)

  • 1685 Replies
  • 832787 Views
Re: Adding new cameras, applying patches into trunk (with source code prepared)
« Reply #1580 on: 06 / September / 2017, 13:50:11 »
Advertisements
Thanks. Is the ?? intended in #258?


Indeed, this was a mistake, thanks. Here is the corrected file.





if (2*b || !2*b) {
    cout<<question
}

Compile error: poor Yorick

*

Offline reyalp

  • ******
  • 14117
Re: Adding new cameras, applying patches into trunk (with source code prepared)
« Reply #1581 on: 06 / September / 2017, 23:40:07 »
Indeed, this was a mistake, thanks. Here is the corrected file.
Thanks, added in trunk 4916
Don't forget what the H stands for.

Re: Adding new cameras, applying patches into trunk (with source code prepared)
« Reply #1582 on: 11 / December / 2017, 18:09:25 »
Port for the G16 attached.  :xmas I've probably procrastinated long enough about releasing this.

Firmware versions 1.00h  & 1.01a are marked ALPHA - SKIP_AUTOBUILD.  Test builds have been downloaded more than 20x each but limited feedback received.

Firmware version 1.01b is marked PREALPHA - SKIP_AUTOBUILD.  Test build recently made available but no feedback so far.

Firmware version 1.01c is marked BETA and it's ready for the autobuild as I've been using it sometime now with no issues.


Ported :   A1200    SD940   G10    Powershot N    G16

*

Offline reyalp

  • ******
  • 14117
Re: Adding new cameras, applying patches into trunk (with source code prepared)
« Reply #1583 on: 11 / December / 2017, 23:51:51 »
Port for the G16 attached.  :xmas I've probably procrastinated long enough about releasing this.
Added in trunk r4958, with some cosmetic cleanup in r4959
Don't forget what the H stands for.


Re: Adding new cameras, applying patches into trunk (with source code prepared)
« Reply #1584 on: 17 / December / 2017, 14:54:21 »
Patch file to update G16 port per G16 Porting Thread
Ported :   A1200    SD940   G10    Powershot N    G16

*

Offline reyalp

  • ******
  • 14117
Re: Adding new cameras, applying patches into trunk (with source code prepared)
« Reply #1585 on: 17 / December / 2017, 17:28:02 »
Patch file to update G16 port per G16 Porting Thread
Thanks. Added in trunk 4961.
Don't forget what the H stands for.

Ported :   A1200    SD940   G10    Powershot N    G16

*

Offline reyalp

  • ******
  • 14117
Don't forget what the H stands for.


Patch for possible UHS SD Card issues per this post :  https://chdk.setepontos.com/index.php?topic=13054.msg136417#msg136417

Tested on the 1.01c - does not cause anything bad to happen but I can't confirm that it fixes anything.

I checked the disassemblies of all four G16 versions and the added address is the same for each.
Ported :   A1200    SD940   G10    Powershot N    G16

*

Offline reyalp

  • ******
  • 14117
Don't forget what the H stands for.

 

Related Topics


SimplePortal 2.3.6 © 2008-2014, SimplePortal