Not saving my pictures - RAW Shooting and Processing - CHDK Forum
« previous next »
Pages: [1]   Go Down

Not saving my pictures

  • 4 Replies
  • 3694 Views
*

Offline itsme

  • *
  • 3
Not saving my pictures
« on: 17 / September / 2011, 06:53:10 »
Advertisements
Hello,

I have a s95 and a flashcard of 16GB partitioned in 2 partitions: 1 of 2GB (FAT16)  and 1 with the rest of the card (FAT32)

I have installed s95-100k-0.9.9-1341-full_BETA on the 2GB. The firmware is booting on the camera and I can make some pictures true USB-triggering. There is just 1 big problem: I can't find the taken pictures!  :'(

I have noticed that file DCIM is not created so I have created it manually but still no luck.

What am I doing wrong?
Logged
*

Offline itsme

  • *
  • 3
Re: Not saving my pictures
« Reply #1 on: 17 / September / 2011, 09:17:57 »
I'm further again.

I figured out that if i take a picture by pressing the button manually then i have a picture.

So the problem is the USB triggering. Here is what i have to do:
http://chdk.wikia.com/wiki/USB_Remote_Cable

Quote
Enable built-in CHDK remote support

You can use a USB remote trigger without a script. First, ensure you are running a reasonably up-to-date CHDK build. Some early builds did not support remote shutter release control via USB. Now enable remote support via the CHDK menu: Main Menu > Miscellaneous Stuff > Remote Parameters > Enable Remote. See User Manual for details.

Now I have to find this setting in the camera and even that is again a struggle  :o
Logged
*

Offline waterwingz

  • ******
  • 12140
    • Waterwingz
Re: Not saving my pictures
« Reply #2 on: 17 / September / 2011, 09:30:34 »
If you don't have USB remote enabled,  then when you apply 5V to the USB port,  the camera switches into "data transfer" mode.  The screen will usually go blank or the camera will "beep" as the camera waits from requests from the computer it thinks is attached to the USB port.   So if that is what you saw, you were not actually taking pictures when you activated your remote USB switch.

Take a look at the diagram just below the text you quoted from the wiki.  It should help explain the various operating modes of the USB remote.

« Last Edit: 17 / September / 2011, 09:34:56 by waterwingz »
Logged
Ported :   A1200    SD940   G10    Powershot N    G16
*

Offline itsme

  • *
  • 3
Re: Not saving my pictures
« Reply #3 on: 17 / September / 2011, 09:59:10 »
Quote from: waterwingz on 17 / September / 2011, 09:30:34
If you don't have USB remote enabled,  then when you apply 5V to the USB port,  the camera switches into "data transfer" mode.  The screen will usually go blank or the camera will "beep" as the camera waits from requests from the computer it thinks is attached to the USB port.   So if that is what you saw, you were not actually taking pictures when you activated your remote USB switch.
Yes you are right.  :)
I wasn't taking pictures  :haha

In the mean time I have discovered the alt menu ( it was well hidden )

Quote
Take a look at the diagram just below the text you quoted from the wiki.  It should help explain the various operating modes of the USB remote.
I did what you write ( diagram)  and after changing some settings it worked.

Thank you very much for your tips.  8)
Logged
*

Offline waterwingz

  • ******
  • 12140
    • Waterwingz
Re: Not saving my pictures
« Reply #4 on: 17 / September / 2011, 10:02:49 »
Quote from: itsme on 17 / September / 2011, 09:59:10
In the mean time I have discovered the alt menu ( it was well hidden )

Some other things you should take a few minutes to look at if you are serious about using CHDK :

CHDK in Brief
CHDK User Manual
CHDK for Dummies
CHDK UserGuide April 2009
CHDK Installation Guide
Logged
Ported :   A1200    SD940   G10    Powershot N    G16
Pages: [1]   Go Up
« previous next »
 

Related Topics


SimplePortal © 2008-2014, SimplePortal