CHDK UI version 2.0 ? - page 45 - General Discussion and Assistance - CHDK Forum
« previous next »
Pages: 1 ... 40 41 42 43 44 [45] 46 47 48 49 50 ... 55   Go Down

CHDK UI version 2.0 ?

  • 542 Replies
  • 144485 Views
*

Offline blackhole

  • *****
  • 942
  • A590IS 101b
    • Planetary astrophotography
Re: CHDK UI version 2.0 ?
« Reply #440 on: 06 / October / 2012, 12:31:39 »
Advertisements
Quote
When I use zoom lever it doesn't change the speed.

Strange to me on the a590 all works without problems.
Logged
*

Offline Pier

  • ***
  • 128
Re: CHDK UI version 2.0 ?
« Reply #441 on: 06 / October / 2012, 13:43:02 »
Also tested tsvstar barnch rev2198.
Override Subj. Dist is OK with Zoom lever on SX130IS
Lever act on every click  to left or right and change the step  by
increment or decrement value with left and right arrow buttons  x1, 10, 100, 1000, 10000
Thanks for the new revision.
Logged
*

Offline outslider

  • *****
  • 762
Re: CHDK UI version 2.0 ?
« Reply #442 on: 07 / October / 2012, 18:23:40 »
@dvip

You are probably in some kind of menu edit mode. Check the setting of profile menu in CHDK settings menu. If any edit mode is enabled, then zoom causes menu lines switching.

Forgive me if above is a little bit confusing, but it's hard to describe the idea when I must to use the word 'menu' in a few different meanings in one sentence:)
Logged
if (2*b || !2*b) {
    cout<<question
}

Compile error: poor Yorick
*

Offline dvip

  • ****
  • 451
Re: CHDK UI version 2.0 ?
« Reply #443 on: 07 / October / 2012, 19:33:35 »
@outslider
Yes, I left it in "Profile Menu [Adv. Edi]" when it should have been in "Profile Menu [On]".
Thanks for checking this out too, blackhole and Pier.
Logged
*

Offline dvip

  • ****
  • 451
Re: CHDK UI version 2.0 ?
« Reply #444 on: 26 / October / 2012, 00:21:41 »
I think there is a minor bug in the tsvstar-uitest branch.
If I use iso80, I get iso100 in my DNG's exif. The jpg is fine, I do get iso80 there.

I am using now  branch release-1_1@2228 and the problem is gone.

Logged
*

Offline waterwingz

  • ******
  • 12140
    • Waterwingz
Re: CHDK UI version 2.0 ?
« Reply #445 on: 26 / October / 2012, 00:28:16 »
Quote from: dvip on 26 / October / 2012, 00:21:41
I think there is a minor bug in the tsvstar-uitest branch.
If I use iso80, I get iso100 in my DNG's exif. The jpg is fine, I do get iso80 there.
I am using now  branch release-1_1@2228 and the problem is gone.
I think I'm having a sense of deja vu all over again here.

http://chdk.setepontos.com/index.php?topic=265.msg90946#msg90946
http://chdk.setepontos.com/index.php?topic=265.msg91234#msg91234

And it was unrelated to the tsvstar branch.

Logged
Ported :   A1200    SD940   G10    Powershot N    G16
*

Offline philmoz

  • *****
  • 3450
    • Photos
Re: CHDK UI version 2.0 ?
« Reply #446 on: 26 / October / 2012, 03:47:04 »
Quote from: waterwingz on 26 / October / 2012, 00:28:16
Quote from: dvip on 26 / October / 2012, 00:21:41
I think there is a minor bug in the tsvstar-uitest branch.
If I use iso80, I get iso100 in my DNG's exif. The jpg is fine, I do get iso80 there.
I am using now  branch release-1_1@2228 and the problem is gone.
I think I'm having a sense of deja vu all over again here.

http://chdk.setepontos.com/index.php?topic=265.msg90946#msg90946
http://chdk.setepontos.com/index.php?topic=265.msg91234#msg91234

And it was unrelated to the tsvstar branch.



http://chdk.setepontos.com/index.php?topic=265.msg92500#msg92500

Phil.
Logged
CHDK ports:
  sx30is (1.00c, 1.00h, 1.00l, 1.00n & 1.00p)
  g12 (1.00c, 1.00e, 1.00f & 1.00g)
  sx130is (1.01d & 1.01f)
  ixus310hs (1.00a & 1.01a)
  sx40hs (1.00d, 1.00g & 1.00i)
  g1x (1.00e, 1.00f & 1.00g)
  g5x (1.00c, 1.01a, 1.01b)
  g7x2 (1.01a, 1.01b, 1.10b)
*

Offline dvip

  • ****
  • 451
Re: CHDK UI version 2.0 ?
« Reply #447 on: 26 / October / 2012, 17:35:01 »
Well, I didn't get the problem using branch release-1_1@2228.
I'm using branch release-1_1@2229 now, and no problem
there either. Haven't tested branch tsvstar-uitest@2229.
Logged
*

Offline philmoz

  • *****
  • 3450
    • Photos
Re: CHDK UI version 2.0 ?
« Reply #448 on: 26 / October / 2012, 17:56:48 »
Quote from: dvip on 26 / October / 2012, 17:35:01
Well, I didn't get the problem using branch release-1_1@2228.
I'm using branch release-1_1@2229 now, and no problem
there either. Haven't tested branch tsvstar-uitest@2229.


The problem is in version 1.2 (trunk) and will probably also be in the tsvstar-uitest branch.

The release-1.1 branch is ok because the new menu code tsvstar added is not in this version.

Phil.
Logged
CHDK ports:
  sx30is (1.00c, 1.00h, 1.00l, 1.00n & 1.00p)
  g12 (1.00c, 1.00e, 1.00f & 1.00g)
  sx130is (1.01d & 1.01f)
  ixus310hs (1.00a & 1.01a)
  sx40hs (1.00d, 1.00g & 1.00i)
  g1x (1.00e, 1.00f & 1.00g)
  g5x (1.00c, 1.01a, 1.01b)
  g7x2 (1.01a, 1.01b, 1.10b)
*

Offline dvip

  • ****
  • 451
Re: CHDK UI version 2.0 ?
« Reply #449 on: 27 / October / 2012, 00:05:06 »
>The problem is in version 1.2 (trunk) and will
>probably also be in the tsvstar-uitest branch.

Yes, the problem is still in the tsvstar-uitest@2229 branch.
Thanks for checking on this, Phil.

I'm using branch release-1_1@2229 and it is working fine.

Logged
Pages: 1 ... 40 41 42 43 44 [45] 46 47 48 49 50 ... 55   Go Up
« previous next »
 

Related Topics
SimplePortal 2.3.6 © 2008-2014, SimplePortal