Canon G12 won't boot with the lastest stable version of CHDK - General Help and Assistance on using CHDK stable releases - CHDK Forum
« previous next »
Pages: [1] 2 3 4   Go Down

Canon G12 won't boot with the lastest stable version of CHDK

  • 32 Replies
  • 17518 Views
*

Offline tome.vardasca

  • *
  • 16
Canon G12 won't boot with the lastest stable version of CHDK
« on: 18 / July / 2012, 17:18:56 »
Advertisements
Hi,

My Canon G12 won't boot with the lastest stable (1.0.0) and the lastest version (1.1.0) of CHDK. The firmware is the 100e, is there any way of logging what happens. The camera turns on but suddenly turns off in every mode.

Best regards
Logged
*

Offline waterwingz

  • ******
  • 12140
    • Waterwingz
Re: Canon G12 won't boot with the lastest stable version of CHDK
« Reply #1 on: 18 / July / 2012, 17:30:12 »
Quote from: tome.vardasca on 18 / July / 2012, 17:18:56
My Canon G12 won't boot with the lastest stable (1.0.0) and the lastest version (1.1.0) of CHDK. The firmware is the 100e, is there any way of logging what happens. The camera turns on but suddenly turns off in every mode.
Is this your first attempt to load CHDK ?    If so,  are you using the right firmware version.   If  its not your first time,  did you download the right firmare version this time ?

Are you attempting to boot using the "firmware update" method or the "SD card lock boot" method ?

Logged
Ported :   A1200    SD940   G10    Powershot N    G16
*

Offline tome.vardasca

  • *
  • 16
Re: Canon G12 won't boot with the lastest stable version of CHDK
« Reply #2 on: 18 / July / 2012, 17:44:36 »
No, is not the first time. I've used previous builds with no problem. Yes I'am using the right version, I've checked it with Acid.
I'm using the "SD card lock boot" method, which is the only supported in G12.
Logged
*

Offline waterwingz

  • ******
  • 12140
    • Waterwingz
Re: Canon G12 won't boot with the lastest stable version of CHDK
« Reply #3 on: 18 / July / 2012, 17:54:23 »
Quote from: tome.vardasca on 18 / July / 2012, 17:44:36
No, is not the first time. I've used previous builds with no problem. Yes I'am using the right version, I've checked it with Acid.
I'm using the "SD card lock boot" method, which is the only supported in G12.
Thanks - that helps to better understand your situation. Do you have an older version to try - just to make sure nothing else has changed ?
Logged
Ported :   A1200    SD940   G10    Powershot N    G16
*

Offline tome.vardasca

  • *
  • 16
Re: Canon G12 won't boot with the lastest stable version of CHDK
« Reply #4 on: 18 / July / 2012, 18:06:14 »
Thank you! No I don't. I overwrite it with the new version :(. Is there any place where I cloud get an old version?
Logged
*

Offline waterwingz

  • ******
  • 12140
    • Waterwingz
Re: Canon G12 won't boot with the lastest stable version of CHDK
« Reply #5 on: 18 / July / 2012, 18:31:33 »
Quote from: tome.vardasca on 18 / July / 2012, 18:06:14
Thank you! No I don't. I overwrite it with the new version :(. Is there any place where I cloud get an old version?

https://www.box.com/chdk#/chdk/1/215559618 has two recent but older "stable" releases frozen in time
Logged
Ported :   A1200    SD940   G10    Powershot N    G16
*

Offline philmoz

  • *****
  • 3450
    • Photos
Re: Canon G12 won't boot with the lastest stable version of CHDK
« Reply #6 on: 18 / July / 2012, 18:32:14 »
Quote from: tome.vardasca on 18 / July / 2012, 17:18:56
Hi,

My Canon G12 won't boot with the lastest stable (1.0.0) and the lastest version (1.1.0) of CHDK. The firmware is the 100e, is there any way of logging what happens. The camera turns on but suddenly turns off in every mode.

Best regards

Very strange - there should not have been any changes recently that would cause this.

You could try deleting (or renaming) the CHDK config files,  CHDK/CCHDK.CFG and CHDK/CCHDK2.CFG and see if that helps.

Phil.
Logged
CHDK ports:
  sx30is (1.00c, 1.00h, 1.00l, 1.00n & 1.00p)
  g12 (1.00c, 1.00e, 1.00f & 1.00g)
  sx130is (1.01d & 1.01f)
  ixus310hs (1.00a & 1.01a)
  sx40hs (1.00d, 1.00g & 1.00i)
  g1x (1.00e, 1.00f & 1.00g)
  g5x (1.00c, 1.01a, 1.01b)
  g7x2 (1.01a, 1.01b, 1.10b)
*

Offline tome.vardasca

  • *
  • 16
Re: Canon G12 won't boot with the lastest stable version of CHDK
« Reply #7 on: 18 / July / 2012, 18:59:27 »
Quote from: philmoz on 18 / July / 2012, 18:32:14
Quote from: tome.vardasca on 18 / July / 2012, 17:18:56
Hi,

My Canon G12 won't boot with the lastest stable (1.0.0) and the lastest version (1.1.0) of CHDK. The firmware is the 100e, is there any way of logging what happens. The camera turns on but suddenly turns off in every mode.

Best regards

Very strange - there should not have been any changes recently that would cause this.

You could try deleting (or renaming) the CHDK config files,  CHDK/CCHDK.CFG and CHDK/CCHDK2.CFG and see if that helps.

Phil.


Thanks. I can't find these files... I'm trying a new installation, could it be any problem in the camera?

One strange thing in the camera is that I have a photo of my own in the starup images, I think that it overwrite the 3rd built in image, and it was when the problems started and I update CHDK.
Logged
*

Offline tome.vardasca

  • *
  • 16
Re: Canon G12 won't boot with the lastest stable version of CHDK
« Reply #8 on: 18 / July / 2012, 19:00:10 »
Quote from: waterwingz on 18 / July / 2012, 18:31:33
Quote from: tome.vardasca on 18 / July / 2012, 18:06:14
Thank you! No I don't. I overwrite it with the new version :(. Is there any place where I cloud get an old version?

https://www.box.com/chdk#/chdk/1/215559618 has two recent but older "stable" releases frozen in time

Thank you very much!
Logged
*

Offline philmoz

  • *****
  • 3450
    • Photos
Re: Canon G12 won't boot with the lastest stable version of CHDK
« Reply #9 on: 18 / July / 2012, 19:02:45 »
Quote from: tome.vardasca on 18 / July / 2012, 18:59:27
Thanks. I can't find these files... I'm trying a new installation, could it be any problem in the camera?

Ok, if it's a new install these files won't be present yet.

Quote
One strange thing in the camera is that I have a photo of my own in the starup images, I think that it overwrite the 3rd built in image, and it was when the problems started and I update CHDK.

Have you tried starting without CHDK and resetting the startup image back to the default?

Phil.
Logged
CHDK ports:
  sx30is (1.00c, 1.00h, 1.00l, 1.00n & 1.00p)
  g12 (1.00c, 1.00e, 1.00f & 1.00g)
  sx130is (1.01d & 1.01f)
  ixus310hs (1.00a & 1.01a)
  sx40hs (1.00d, 1.00g & 1.00i)
  g1x (1.00e, 1.00f & 1.00g)
  g5x (1.00c, 1.01a, 1.01b)
  g7x2 (1.01a, 1.01b, 1.10b)
Pages: [1] 2 3 4   Go Up
« previous next »
 

Related Topics


SimplePortal © 2008-2014, SimplePortal