Can I create bootable SD card without the small locking switch? - Hello, I'm a NEWBIE - HELP!! (Newbies assistance, User Guides and thank you notes) - CHDK Forum
« previous next »
Pages: [1]   Go Down

Can I create bootable SD card without the small locking switch?

  • 6 Replies
  • 6378 Views
*

Offline thangggg123

  • *
  • 10
Can I create bootable SD card without the small locking switch?
« on: 19 / April / 2013, 05:52:42 »
Advertisements
Hello everyone! I lost my 2GB SD card's locking switch (the little one on the left side of the card), so can I make my SD card bootable? Thank you very much!
P.S: I repaired my card with this instruction: Fix Broken SD Card Lock Can I make my SD card bootable?
« Last Edit: 19 / April / 2013, 05:54:56 by thangggg123 »
Logged
*

Offline waterwingz

  • ******
  • 12140
    • Waterwingz
Re: Can I create bootable SD card without the small locking switch?
« Reply #1 on: 19 / April / 2013, 07:37:47 »
Quote from: thangggg123 on 19 / April / 2013, 05:52:42
Can I make my SD card bootable?
If you followed those instructions,  you will need to remove the section of paperclip that you glued in.  As the guy in the video said "Good luck".
Logged
Ported :   A1200    SD940   G10    Powershot N    G16
*

Offline thangggg123

  • *
  • 10
Re: Can I create bootable SD card without the small locking switch?
« Reply #2 on: 19 / April / 2013, 08:54:03 »
Is there any solution to my problem other than removing the paper clip I glued into my SD card, waterwingz?
Logged
*

Offline waterwingz

  • ******
  • 12140
    • Waterwingz
Re: Can I create bootable SD card without the small locking switch?
« Reply #3 on: 19 / April / 2013, 14:10:51 »
Quote from: thangggg123 on 19 / April / 2013, 08:54:03
Is there any solution to my problem other than removing the paper clip I glued into my SD card, waterwingz?
Well,  you could modify the SD card slot in your camera by bending the SD card lock detection lever so that it permanently does not see the SD card lock switch.  But you probably don't want to make such a permanent modification to your camera.

There is no software solution (CHDK or otherwise) to your problem.   Your camera only loads CHDK because it sees the SD card lock in the locked position.

But 2G SD cards are really cheap - just buy a new one to use with CHDK.

« Last Edit: 19 / April / 2013, 15:35:10 by waterwingz »
Logged
Ported :   A1200    SD940   G10    Powershot N    G16
*

Offline thangggg123

  • *
  • 10
Re: Can I create bootable SD card without the small locking switch?
« Reply #4 on: 20 / April / 2013, 00:12:42 »
okay, thank you for your help, waterwingz! I'll buy a new one!  ::)
Logged
*

Offline waterwingz

  • ******
  • 12140
    • Waterwingz
Re: Can I create bootable SD card without the small locking switch?
« Reply #5 on: 20 / April / 2013, 01:20:01 »
Quote from: thangggg123 on 20 / April / 2013, 00:12:42
okay, thank you for your help, waterwingz! I'll buy a new one!  ::)
Or you can use the "firmware update" method to load CHDK each time you start your camera.
Logged
Ported :   A1200    SD940   G10    Powershot N    G16
*

Offline thangggg123

  • *
  • 10
Re: Can I create bootable SD card without the small locking switch?
« Reply #6 on: 20 / April / 2013, 04:26:49 »
I'm lazy, you know! Anyway, thank you so much for your help!  :)
Logged
Pages: [1]   Go Up
« previous next »
 

Related Topics


SimplePortal © 2008-2014, SimplePortal