A4000IS porting thread - page 21 - DryOS Development - CHDK Forum  
« previous next »
Pages: 1 ... 16 17 18 19 20 [21]   Go Down

A4000IS porting thread

  • 205 Replies
  • 71566 Views
*

Offline nafraf

  • *****
  • 1308
Re: A4000IS porting thread
« Reply #200 on: 02 / May / 2014, 00:09:49 »
Advertisements
Quote from: Schnappschuss on 01 / May / 2014, 15:41:25
I'm not completely sure I did everything the way it is supposed to be done but I got some results.
Thanks for testing.  llibtst.lua run without problems.
set_mode seems to works, there are some problems probably due to not enough delay.
To run mftest.lua please setup camera as described in wiki page, camera was in auto, but P mode is required, please disable AF and servo AF.
Could you check if raw capture works?
I think it is enough to include port in autobuild.

Logged
*

Offline Schnappschuss

  • *
  • 9
Re: A4000IS porting thread
« Reply #201 on: 02 / May / 2014, 16:09:55 »
Quote from: nafraf on 02 / May / 2014, 00:09:49
To run mftest.lua please setup camera as described in wiki page, camera was in auto, but P mode is required, please disable AF and servo AF. Could you check if raw capture works?
P mode? As in manual? Do I use CHDK for that? Otherwise there are no modes as far as I can see. The camera is pretty dumb - just turn it on and shoot. There are no AF options in the original firmware or is that a CHDK feature?

[edit] Found the P mode.
« Last Edit: 02 / May / 2014, 16:17:32 by Schnappschuss »
Logged
*

Offline reyalp

  • ******
  • 14082
Re: A4000IS porting thread
« Reply #202 on: 02 / May / 2014, 16:19:37 »
Quote from: Schnappschuss on 02 / May / 2014, 16:09:55
Quote from: nafraf on 02 / May / 2014, 00:09:49
To run mftest.lua please setup camera as described in wiki page, camera was in auto, but P mode is required, please disable AF and servo AF. Could you check if raw capture works?
P mode? As in manual? Do I use CHDK for that? Otherwise there are no modes as far as I can see. The camera is pretty dumb - just turn it on and shoot. There are no AF options in the original firmware or is that a CHDK feature?
These are Canon firmware features. If you don't have the original manual, it's available for download form Canon
http://www.usa.canon.com/cusa/support/consumer/digital_cameras/powershot_a_series/powershot_a4000_is#BrochuresAndManuals

Chapter 4 covers P mode. Servo AF is also described there.
Logged
Don't forget what the H stands for.
*

Offline Schnappschuss

  • *
  • 9
Re: A4000IS porting thread
« Reply #203 on: 02 / May / 2014, 16:36:11 »
@reyalp
Thanks a lot!

Saving as RAW (DNG) works.
Logged
*

Offline nafraf

  • *****
  • 1308
Re: A4000IS porting thread
« Reply #204 on: 03 / May / 2014, 09:26:04 »
Quote from: Schnappschuss on 02 / May / 2014, 16:36:11
Saving as RAW (DNG) works.
Thanks!
A4000 100c enabled in autobuild. Changeset 3431
Logged
*

Offline Schnappschuss

  • *
  • 9
Re: A4000IS porting thread
« Reply #205 on: 04 / May / 2014, 13:08:45 »
Thank you! Is there anything else I can do to help porting it to the A4000?
Logged
Pages: 1 ... 16 17 18 19 20 [21]   Go Up
« previous next »
 

Related Topics