Powershot SX150 IS Porting Thread - page 13 - General Discussion and Assistance - CHDK Forum
« previous next »
Pages: 1 ... 8 9 10 11 12 [13] 14 15 16 17 18 ... 28   Go Down

Powershot SX150 IS Porting Thread

  • 279 Replies
  • 115368 Views
*

Offline hiker_jon

  • ****
  • 284
Re: Powershot SX150 IS Porting Thread
« Reply #120 on: 20 / January / 2012, 10:27:39 »
Advertisements
I tested it this morning: Behavior is same, no raw saved.
Jon

Quote from: philmoz on 20 / January / 2012, 02:53:33

Try the attached test version.

Phil.

Update: replaced the attachment. Previous version was missing the changes added earlier by reyalp.

Logged
*

Offline philmoz

  • *****
  • 3450
    • Photos
Re: Powershot SX150 IS Porting Thread
« Reply #121 on: 20 / January / 2012, 15:21:46 »
Quote from: hiker_jon on 20 / January / 2012, 10:27:39
I tested it this morning: Behavior is same, no raw saved.
Jon

Quote from: philmoz on 20 / January / 2012, 02:53:33

Try the attached test version.

Phil.

Update: replaced the attachment. Previous version was missing the changes added earlier by reyalp.


Can you post all the settings from the RAW Parameters menu, and which mode the camera is in (Auto, P, etc).
Also try running the 'Create badpixel.bin' command from the same menu and let me know what happens (will help determine where it's getting in the code).

Phil.
Logged
CHDK ports:
  sx30is (1.00c, 1.00h, 1.00l, 1.00n & 1.00p)
  g12 (1.00c, 1.00e, 1.00f & 1.00g)
  sx130is (1.01d & 1.01f)
  ixus310hs (1.00a & 1.01a)
  sx40hs (1.00d, 1.00g & 1.00i)
  g1x (1.00e, 1.00f & 1.00g)
  g5x (1.00c, 1.01a, 1.01b)
  g7x2 (1.01a, 1.01b, 1.10b)
*

Offline hiker_jon

  • ****
  • 284
Re: Powershot SX150 IS Porting Thread
« Reply #122 on: 21 / January / 2012, 01:39:50 »
I delete cchdk.cfg before starting so all is the default except I turn save raw on.
exceptions: non checked, warn on, crw,.cr2,... dng not checked.

When I execute create badpixel.bin it takes one picture that is all.  the file is not created.

Jon

Quote from: philmoz on 20 / January / 2012, 15:21:46

Can you post all the settings from the RAW Parameters menu, and which mode the camera is in (Auto, P, etc).
Also try running the 'Create badpixel.bin' command from the same menu and let me know what happens (will help determine where it's getting in the code).

Phil.

Logged
*

Offline philmoz

  • *****
  • 3450
    • Photos
Re: Powershot SX150 IS Porting Thread
« Reply #123 on: 21 / January / 2012, 01:53:31 »
Quote from: hiker_jon on 21 / January / 2012, 01:39:50
I delete cchdk.cfg before starting so all is the default except I turn save raw on.
exceptions: non checked, warn on, crw,.cr2,... dng not checked.

When I execute create badpixel.bin it takes one picture that is all.  the file is not created.

Jon

Quote from: philmoz on 20 / January / 2012, 15:21:46

Can you post all the settings from the RAW Parameters menu, and which mode the camera is in (Auto, P, etc).
Also try running the 'Create badpixel.bin' command from the same menu and let me know what happens (will help determine where it's getting in the code).

Phil.


When you start CHDK does the splash logo show straight away or only after about 4 seconds?
In AV or TV mode, if you enter CHDK <ALT> mode then turn the rear dial does the Canon AV or TV value still change?

I know these are unrelated; but will help me track the source of the problem. The boot code does not look correct to me so I'm trying to see if the CHDK tasks are running.

Phil.
Logged
CHDK ports:
  sx30is (1.00c, 1.00h, 1.00l, 1.00n & 1.00p)
  g12 (1.00c, 1.00e, 1.00f & 1.00g)
  sx130is (1.01d & 1.01f)
  ixus310hs (1.00a & 1.01a)
  sx40hs (1.00d, 1.00g & 1.00i)
  g1x (1.00e, 1.00f & 1.00g)
  g5x (1.00c, 1.01a, 1.01b)
  g7x2 (1.01a, 1.01b, 1.10b)
*

Offline coronagmbh

  • *
  • 4
Re: Powershot SX150 IS Porting Thread
« Reply #124 on: 21 / January / 2012, 11:10:06 »
I'm following this thread now, having the same problem. Perhaps I can also help in some way.
After switching on, it takes some seconds and then the orange CHD.. appears.
IN AV and TV mode, going to CHDK <alt>, AV and TV are still changing.
Can I do additional tests for you?

hc
Logged
*

Offline hiker_jon

  • ****
  • 284
Re: Powershot SX150 IS Porting Thread
« Reply #125 on: 21 / January / 2012, 12:00:41 »
It does take 4 secs for the logo to appear. I had noticed the delay.  When in <alt> mode and Av or Tv the aperture or shutter speed still change when you move the back dial.
Jon
Quote from: philmoz on 21 / January / 2012, 01:53:31

When you start CHDK does the splash logo show straight away or only after about 4 seconds?
In AV or TV mode, if you enter CHDK <ALT> mode then turn the rear dial does the Canon AV or TV value still change?

I know these are unrelated; but will help me track the source of the problem. The boot code does not look correct to me so I'm trying to see if the CHDK tasks are running.

Phil.

Logged
*

Offline coronagmbh

  • *
  • 4
Re: Powershot SX150 IS Porting Thread
« Reply #126 on: 21 / January / 2012, 12:11:56 »
Yes, still changing, even in <alt> mode.

hc
Logged
*

Offline philmoz

  • *****
  • 3450
    • Photos
Re: Powershot SX150 IS Porting Thread
« Reply #127 on: 21 / January / 2012, 15:42:46 »
Quote from: hiker_jon on 21 / January / 2012, 12:00:41
It does take 4 secs for the logo to appear. I had noticed the delay.  When in <alt> mode and Av or Tv the aperture or shutter speed still change when you move the back dial.
Jon

That's what I thought. This means that none of the task overrides are being activated so most of the advanced CHDK functions won't work.

I'll need to review all the code before activating the tasks, since they may crash the camera if they have not been done correctly. I don't have this camera so I can't test any changes directly.

Keep watching this space for updates :)

Phil.

Update: The task code looks ok, attached is another test version (fingers crossed).

« Last Edit: 21 / January / 2012, 16:50:56 by philmoz »
Logged
CHDK ports:
  sx30is (1.00c, 1.00h, 1.00l, 1.00n & 1.00p)
  g12 (1.00c, 1.00e, 1.00f & 1.00g)
  sx130is (1.01d & 1.01f)
  ixus310hs (1.00a & 1.01a)
  sx40hs (1.00d, 1.00g & 1.00i)
  g1x (1.00e, 1.00f & 1.00g)
  g5x (1.00c, 1.01a, 1.01b)
  g7x2 (1.01a, 1.01b, 1.10b)
*

Offline hiker_jon

  • ****
  • 284
Re: Powershot SX150 IS Porting Thread
« Reply #128 on: 21 / January / 2012, 17:23:55 »
The logo appears right away now and the aperture and shuutter speed settings do not change in <alt> mode, but raw is still broken, behaves the same.

Quote from: philmoz on 21 / January / 2012, 15:42:46

Update: The task code looks ok, attached is another test version (fingers crossed).

Logged
*

Offline philmoz

  • *****
  • 3450
    • Photos
Re: Powershot SX150 IS Porting Thread
« Reply #129 on: 21 / January / 2012, 17:38:14 »
Quote from: hiker_jon on 21 / January / 2012, 17:23:55
The logo appears right away now and the aperture and shuutter speed settings do not change in <alt> mode, but raw is still broken, behaves the same.

Quote from: philmoz on 21 / January / 2012, 15:42:46

Update: The task code looks ok, attached is another test version (fingers crossed).


Does the 'create badpixel.bin' option work now?
Also try setting the option to save the RAW in the same directory as the JPEG.

Phil.
Logged
CHDK ports:
  sx30is (1.00c, 1.00h, 1.00l, 1.00n & 1.00p)
  g12 (1.00c, 1.00e, 1.00f & 1.00g)
  sx130is (1.01d & 1.01f)
  ixus310hs (1.00a & 1.01a)
  sx40hs (1.00d, 1.00g & 1.00i)
  g1x (1.00e, 1.00f & 1.00g)
  g5x (1.00c, 1.01a, 1.01b)
  g7x2 (1.01a, 1.01b, 1.10b)
Pages: 1 ... 8 9 10 11 12 [13] 14 15 16 17 18 ... 28   Go Up
« previous next »
 

Related Topics